809329
24
Zoom out
Zoom in
Previous page
1/28
Next page
ENERGY SAVINGS
6 720 802 172 (2012/06)24
15 ENERGY SAVINGS
INSPECTION AND MAINTENANCE
To achieve as low energy consumption as possible for a longer period of
time, we recommend that you have an annual service and any
maintenance carried out by a competent person.
UNDERFLOOR HEATING
Do not set a flow temperature that is higher than the highest value
recommended by the floor manufacturer.
AIRING
Do not leave the windows ajar when you air. This makes heat leave the
room all the time, but the air quality in the room does not improve.
Instead, open the windows fully for a short time.
ADDITIONAL ELECTRIC HEAT
Different settings (e.g. extra hot water) lead to the activation of an
additional electric heat source and thereby to higher energy
consumption.
Always select a temperature setting for hot water and heating that is as
low as possible.
16 MAINTENANCE
The heat pump requires minimal upkeep. Some inspection is
recommended nevertheless for the heat pump to perform as well as
possible. Check the following points a couple of times during the first
year. Subsequently they should be checked occasionally during the
year:
Safety valves
Expansion vessel (plastic vessel collector circuit)
Particle filter
16.1 CHECKING THE SAFETY VALVES
Check that the waste water hose from the safety valve is not blocked.
16.2 EXPANSION VESSEL
A plastic expansion vessel is connected to the heat pump collector
circuit ("the cold side"). The level in the vessel must not be less than
minimum level 1/3. If the fluid level is too low, contact your installer.
16.3 PARTICLE FILTER
The particle filter (dirt filter) ensures that no particles or dirt get into the
heat exchangers. In time, the filter can become clogged and must be
cleaned. There are particle filters on both the "hot and cold sides". The
particle filter should be cleaned as follows:
Switch off the heat pump with the ON/OFF button.
Shut the valve and screw off the sealing lid.
Release the locking ring which holds the sieve in the valve. Use the
accompanying locking ring bar. (Image 32)
Lift the sieve out from the valve and rinse it clean with water.
Replace the sieve, the locking ring and the sealing lid.
Open the valve and start the heat pump with the ON/OFF button.
Fig. 32
17 THE GUARANTEE
The Greenstore Liquid to Water heat pump has a 2 year guarantee
against faulty material or manufacture subject to Terms and conditions.
To read the full Terms and Conditions please visit us online at
www.worcester-bosch.co.uk/guarantee. The Guarantee Registration
form is available on this same page and can be completed and submitted
electronically. Alternatively please telephone one of our Guarantee
Registration advisors on 0844 892 2552. Your statutory rights are not
affected by the manufacturers guarantee.
The safety valve should be checked by a qualified
engineer - usually as part of an annual service visit.
Never close the safety valve or obstruct it’s discharge
pipe.
6 720 613 623-05.1R
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester Greenstore Ground Source at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester Greenstore Ground Source in the language / languages: English as an attachment in your email.

The manual is 3.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info