809346
8
Zoom out
Zoom in
Previous page
1/24
Next page
8
Installation
Comfort I – 6720810964 (2014/07)
Turn the knob to select Radio settings
Press the knob to display Pairing, that is RF pairing of the
devices in the system
Turn the knob to display Unpairing or Pairing
▶If Pairing is chosen, press the knob and pairing is displayed
with advancing bars.
When the pairing between the devices has been made the
number 1 is displayed confirming the Room thermostat is
connected
▶If Unpairing is chosen, press the knob and Unpairing is
displayed with advancing bars, when the unpairing
between the devices has been made the number 0 is
displayed confirming that the Room thermostat has been
disconnected
3.4.2 Room Thermostat - Settings- rF 1 Pair
To enter the Settings menu:
1. Press the knob until the two bars are displayed
2. Release the knob to enter the Settings menu
Fig. 5 Settings
The following sub-menus are available:
1. E 1 Room temperature sensor adjustment
2. F 1 Factory reset
3. rF 1 Pairing/Unpairing
4. S 1 Software version
5. S 2 RF signal strength indication
Turn the knob to select rF 1 and press
Turning the knob will display A or d
▶To Pair the Room thermostat with the Programmer/
Receiver, turn the knob to select A
Press the knob to start the pairing process, the
Programmer/Receiver has to be in the same mode.
During the pairing process 0 flashes until the units are
connected and then 1 will be displayed flashing, when the
pairing is completed A is displayed. Either wait 30 seconds and
the display will revert to displaying the current room
temperature, to move to the next higher level, press the knob
for more than three seconds and when the bars are displayed,
release the knob.
To leave the menu and display current room temperature,
press the knob again for more than three seconds and when the
bars are displayed, release the knob to display the current
room temperature.
▶To Unpair (disconnect) the units, turn the knob to select d
Press the knob to start the unpairing (disconnection), a 1
will be displayed flashing, when the unpairing is completed
a flashing 0 will be displayed and when the process is
complete, d is displayed
When the unit(s) have been unpaired or disconnected a
zero will be displayed indicating that no units are
connected.
Press the knob, for more than three seconds, to return to the
previous level, rF 1.
Press the knob until the three bars are displayed and release
the knob to display the current room temperature.
3.5 Room thermostat mounting
The Room thermostat is a radio frequency (RF) device and as
such is flexible for positioning, there is no requirement to hard
wire the device.
The Room thermostat requires free air flow and should be
mounted in an open area and not obscured by curtains or
furniture. The thermostat should be mounted no closer than
300mm to metal objects, including metal wall boxes.
Mount the thermostat on a wall that is not subject to direct
sunlight or draughts, preferably on an inside wall at 1.2 metres
above the floor.
If a fault code is displayed the user must first
press the knob to return to the main display then
the user can hold the knob to enter the Settings
menu
6720810964-17.1Wo
6720810964-12.1Wo
6720810964-08.1Wo
6720810964-09.1Wo
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch Greenstar Comfort I RF - 2014-2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch Greenstar Comfort I RF - 2014-2022 in the language / languages: English as an attachment in your email.

The manual is 4.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info