809346

Worcester-Bosch Greenstar Comfort I RF - 2014-2022 Manual

7
Zoom out
Zoom in
Previous page
1/24
Next page
7
Installation
Comfort I– 6720810964 (2014/07)
Fig. 3 Suggested Programmer wall plate mounting
▶ Engage the four clips on the back of the Programmer [2]
with the four slots on the wall plate as shown in figure 4
▶ Push the Programmer down into the wall plate to secure
▶ Engage the tabs on the top retainer [3] into the slots on the
wall plate [1] and push down onto the Programmer
Fig. 4 Fitting Timer to wall plate assembly
3.3 Time and date set up
▶Turn the boiler ON
▶ Fit the batteries into the Room thermostat, refer to
section 9.1 for instruction on how to fit the batteries
Before mounting the Room thermostat on the wall, it is good
practice to find a position that affords good signal strength.
To check the signal strength, refer to section 6.7 S2 RF Signal
strength on page 18.
The unit will initially display an error code A21 “No wireless
signal to EMS interface”, refer to chapter 7 for information on
fault codes.
When they have established RF communications with each
other, the Programmer/Receiver display will revert to a factory
default time and date with the control in “Auto” mode for both
heating and hot water.
The Room thermostat will display the current room
temperature.
3.4 Pairing/Unpairing the units
3.4.1 Programmer/Receiver - Installer menu -
Radio settings - Pair
The Room thermostat and Programmer/Receiver must be in
the same mode of pairing.
The Programmer/Receiver Pairing/Unpairing function is found
under the Installer menu, in Radio settings and Pair.
To enter the Installer menu, press the menu button and return
button for more than three seconds.
Six icons are shown across the top of the display:
1. Heating
2. Hot water
3. Holiday
4. Info
5. Settings
6. Installer setting
Turn the knob to select the Installer icon and press the
knob to enter the function.
The Programmer/Receiver and Room
Thermostat are factory set and “Paired” to
each other, so that they are fully operational.
6720810964-24.1Wo
6720810964-25.1Wo
1
2
3
Set the current time and date
▶ Hold the menu button down for more than
3 seconds to enter the user menu, turn the
knob to select Settings and press to enter
▶ Refer to section 5.1.5 Info - Time/Date
for setting the Time and Date, and clock
format
The Programmer/Receiver and Room
thermostat are delivered together and are
factory paired, they automatically connect
when the system is switched on. There is no
need to pair/unpair the units during
installation, unless there is a problem with
one or both of the units.
If a faulty unit is replaced with a new unit, then
the existing unit must be unpaired before the
two units can be paired.
If the units have to be paired/unpaired, all units
must be in the same pairing/unpairing mode.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch Greenstar Comfort I RF - 2014-2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch Greenstar Comfort I RF - 2014-2022 in the language / languages: English as an attachment in your email.

The manual is 4.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info