517926
12
Zoom out
Zoom in
Previous page
1/106
Next page
12
G
Maintenance
General
1 Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still
always run on even when the motor is switched off.
Wear protective gloves.
z Store the appliance in a dry location out of the reach of
children.
Cleaning
1 Remove the mains plug before any maintenance and
cleaning work!
z Handle the appliance with care and clean it regularly to
prolong its service life.
z Keep the ventilation slits clean and dust-free.
z Only use a warm and moist cloth to clean the appliance as well
as a soft brush.
z Do not allow the appliance to get wet and do not spray with
water.
Setting the cutting unit
3 The cutting unit is factory set and must not be set
during the first commissioning.
1. Switch on appliance.
2. Turn the adjustment knob clockwise until grinding noises are
audible and fine aluminium chips fall from the discharge chute
(worn points on the cutting plate are optimally balanced. The
chopping material is then better cut through).
Fixing problems
F
Problem Possible cause Solution
Motor does not start.
z Not connected to voltage supply z Check protection
z Faulty connection cable
z Appliance overloaded (the motor is equipped with a
circuit breaker and automatically switches off in the
event of overloading).
z Check the cable (electrical expert)
z The motor can be switched back on after
a cooling down break (ca. 5 min.).
Motor hums but does not
start
z Cutting roller blocked z Change direction of rotation, proceed to
switch off appliance and clean.
z Faulty capacitor z Give appliance to authorised WOLF
customer service centre for repair.
Chopping material is not
pulled in
z Incorrect switch position
z Chopping material trapped in the hopper
z Too soft or wet chopping material
z Wear on the cutting roller
z Adjust direction of rotation
z Change direction of rotation, proceed to
switch off appliance and clean.
z Push with a branch and chop through
z Set cutting unit
Chopping material is not
cleanly cut through
z Profile plate not set sufficiently. z Set cutting unit.
When in doubt, always seek out a WOLF Service location.
Attention: Put down the appliance and pull out the power plug before performing any checks or work on the blades.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten SDL 2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten SDL 2500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info