517925
10
Zoom out
Zoom in
Previous page
1/90
Next page
10
G
Switching on / off
Press the green button to switch on (2)
z Press the red button to switch off (3)
3 The machine has a circuit breaker to prevent switching
back on unintentionally after a power cut.
Overload protection
3 An overloading of the appliance (e.g. culminating in the
blocking of the blades) can lead to the standstill of the
appliance after a few seconds. To protect the motor
from damage the appliance is automatically discon-
nected from the mains by the overload protection.
z Before putting into operation again wait for at least one
minute before immediately pressing the reset button
(1) and then ON/OFF switch. If the motor does not
start, clean the collection hopper (see Maintenance).
Special instructions for chopping
z Chop branches, twigs and wood shortly after cutting (this
chopped material will become very hard once it has dried out,
therefore the maximum diameter which can be processed is
less).
z Remove the side shoots on severely ramified branches.
z When processing garden or kitchen waste with a high water
content with a tendency to stick, crush alternately with wooden
chopping material to avoid blocking the appliance.
z Do not allow the chopping material in the area of the discharge
opening to accumulate too high. This can lead to material
which is already chopped blocking the discharge channel.
This can cause a kickback of the material through the filling
opening.
z Ensure that the maximum branch diameter for processing per-
mitted for your appliance is observed.
z The blade unit pulls in the chopping material largely by itself.
z Do not overload or block the motor in the case of tough
branches by frequently pulling back the branch.
Maintenance
General
1 Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still
always run on even when the motor is switched off.
Wear protective gloves.
z Store the appliance in a dry location out of the reach of chil-
dren.
General cleaning information
1 Remove the mains plug before any maintenance and
cleaning work!
z Handle the appliance with care and clean it regularly to pro-
long its service life.
z Keep the ventilation slits clean and dust-free.
z Only use a warm and moist cloth to clean the appliance as well
as a soft brush.
z Do not allow the appliance to get wet and do not spray with
water.
Cleaning the collection hopper
1 Remove the mains plug before any maintenance and
cleaning work!
1. Unscrew the knob and fold the casing upwards to open .
2. Clean the cutting and discharge area of all objects which could
block the blades.
3. Close the casing again and tighten the knob .
4. Press the reset button before activating the ON/OFF switch.
Safety locking device
z The chopper is equipped with a safety locking device at the
lock between the casing and the motor casing.
z In the event that the casing does not close flush to the motor
casing, the motor is stopped by the safety locking device.
z In such a case, proceed as follows:
Unscrew the knob and fold the casing upwards to open .
Carefully clean the contact surfaces.
Close the casing again and tighten the knob .
Changing blades
1 Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still
always run on even when the motor is switched off.
For safety reasons, always have the blades changed by
an authorised service centre.
1. Unscrew the knob and fold the casing upwards to open .
2. In order to change the blades insert the hexagon spanner
(1) in the slot on the retaining plate and through the cover.
3. Loosen the two screws with the Allen spanner
(2) and
take out the worn blades.
4. Insert the new blades and tighten the screws.
1 Remove both the Allen and hexagon spanner after com-
pleting the change.
5. Close the casing again and tighten the knob .
F
F
F
G
G
G
G
G
H
G
H
H
G
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten SDE 2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten SDE 2500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info