638677
13
Zoom out
Zoom in
Previous page
1/42
Next page
13
G
Emptying of Grassbox
When the collection bag is full, the flap lowers by itself.
1 Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Empty collection bag.
z Remove potential blockages in the cutting space before
starting.
3 Instructions for level indicator:
For an efficient functioning of the level indicator, regularly
clean the holes under the level indicator in the collection
bag with a hand brush.
Tips for mowing
z To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters .
Maintenance
General
1 Caution! Rotating blades
Before all maintenance and cleaning tasks:
z Remove the sparking plug lead.
z Take care not to grab running cutters.
z For safety reasons, replace any worn or damaged parts.
When replacing, follow the instructions for installation
z Check all the visible fastening bolts and nuts regularly to be
sure they are snug and tighten them.
z Only use spare parts made by WOLF-Garten; otherwise you
do not have a guarantee that your mower meets safety regu-
lations.
Cleaning operations and blade change
1. Pull off the sparkplug connector!
2. Raise the cutting height to its highest position .
3. For cleaning and changing the blade, tip the mower to the side
as illustrated .
Sharpening and changing blade
1 Caution! Rotating blades
Before all maintenance and cleaning tasks:
z Remove the sparking plug lead.
z Take care not to grab running cutters.
z Change of blades only be carried out by an approved service
station.
z Gloves should be worn at all times when working on the blade.
Remove ignition key and spark plug lead when working on the
blade.
z Damaged blades should always be replaced in pairs to ensure
even balance.
3 Information for Service Centre, blade retaining screw to
be tightened to:
A/F 17 mm = 38-42 Nm / A/F 13 mm = 16-20 Nm
Adjusting the Bowden cable coupling
1. Raise the drive bracket (3) app. 2 cm and hold.
2. Loosen the locking nut (1).
3. Turn the setscrew (2) left until the drive wheels are blo-
cked when you pull the mower backwards.
4. Tighten locking nut (1).
Change oil only
z While engine is warm and fuel tank empty.
z Change oil after the first 5 working hours. There after change
engine oil every 25 working hours and at the end of the mo-
wing season. Change engine oil more frequently if working un-
der extreme and dusty conditions.
1. Remove oil filler cap.
2. Tilt machine slowly to side and allow oil to drain from the
crankcase through the filler .
3. Oil Fill .
Cleaning of Spark Plug
z Check and clean regularly
z Reset plug gap as required (0,76 mm).
Cleaning of air filter
Refer to the engine manufacturer‘s handbook supplied.
N
O
M
P
Q
H
R
R
R
S
K
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten Power Edition 46 B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten Power Edition 46 B in the language / languages: English, German, Dutch, French, Italian, Turkish as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info