813078
3
Zoom out
Zoom in
Previous page
1/4
Next page
Page 3 / 4
© Wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue 03/2011 Art. No. 950 325
Error Codes
In the event of errors of error class 1 (F1) use the error code to find the cause of the error, rectify the error and then
do a reset by pressing the I/O key. In the event of class 2 errors (F2) the stove automatically carries out a reset as
soon as the cause has been eliminated.
Display
mesage Error class (F1) or (F2) / Cause of error
RE
Er1 (F1) – Bridge wire at “auxiliary input” (RE) open or error in external component/device connected to it.
PE
Err (F1) – Fuel level (error message “PE Res”) permanently below reserve line / minimum filling level for
longer than 5 minutes Î replenish pellets!
RO
Err (F1) – Grate hasn’t reached “open“ position (RO) Î ashpit full (Æclear ashpit). Swivelling grate
possibly soiled / jammed or grate motor / limit switch / grate axis driver / cabling defective.
RG
Err (F1) – Grate hasn’t reached “closed“ position (RG) Î ashpit full (Æclear ashpit). Swivelling grate
possibly soiled / jammed or grate motor / limit switch / grate axis driver / cabling defective.
Z
Err (F1) – Ignition error. Flue gas temperature (TR) hasn’t risen to the required degree after starting.
ST (F1) – STB (a safety device) has triggered. Temperature at heat exchanger too high
TR (F1) – Flue gas temperature (TR) too low during operation
TR Er1 (F1) – Flue gas temperature sensor (TR) broken
TP (F1) – Temperature at pellet chute (sensor TP) too high
TP Er1 (F1) – Pellet chute temperature sensor (TR) broken
TP Er2 (F1) – Pellet chute temperature sensor (TP) shorted
HB Er1 (F1) – Defect in operating panel/operating panel cable or communication with TC1 Touch Control
(optional)
HP Er1 (F1) – 24 V inputs to main circuit board defective or wrongly connected
HP Er2 (F1) – Reference temperature sensor on main circuit board defective
HP Er3 (F1) – Write/Read error by EEPROM on main circuit board
LM Er1 (F1) – Air flow sensor (LM) broken
LM Er2 (F1) – Air flow sensor (LM) shorted
TL HI (F1) – Temperature at air flow sensor (TL) too high
TL Grd (F1) – Temperature gradient at air flow sensor too high
TW Er1 (F2) – Temperature sensor in heat exchanger (TW) broken
TW Er2 (F2) – Temperature sensor in heat exchanger (TW) shorted
L- LO (F2) – Lower air flow limit exceeded
RA Err (F1) – Cleaning (1.0 t) severely overdue
WA Err (F1) – Servicing (3.0 t) severely overdue
AL Err (F1) – Ashpit door open during operation
PL Err (F1) – Fuel hopper open for too long
FT Err (F1) – Firedoor open during operation
R4 Er1 (F1) – “auxiliary output 4” (safety relay) defective
GD Err Î Currently not active
BU Er1 (F2) – BUS error (defect in bus communication or input RS 485)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Ivo.tec S5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Ivo.tec S5 in the language / languages: English as an attachment in your email.

The manual is 0.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Ivo.tec S5

Wodtke Ivo.tec S5 User Manual - German - 80 pages

Wodtke Ivo.tec S5 User Manual - French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info