813078
2
Zoom out
Zoom in
Previous page
1/4
Next page
Page 2 / 4
© Wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue 03/2011 Art. No. 950 325
Display Messages
Display
message Explanation
“Standby dot”; appliance has been switched off manually via I/O key. Press the I/O key to switch on the stove. The stove
does not respond to external controllers when in standby mode.
ON ON start signal (appears briefly when you switch on the stove)
The stove has been started. After briefly showing the programme being used it enters the TEST phase.
OFF OFF stop signal (appears briefly or alternates with “A” for 4 minutes when you switch off the stove)
The stove has been switched off and after going through phases A1 – A4 enters fan after-run phase G OFF.
B1
001
This is the programme and programme version (appears for some seconds during start-up).
B1 = programme 3 – 9 kW; B2 = programme 3 – 11 kW; B3 = programme 3 – 13 kW; B4 = programme 3 – 13 kW
001 = programme version 1; 002 = programme version 2; flashes alternately with TEst (see below).
TE
st
TEST phase (appears after starting the stove)
Checks all stove functions; flue gas exhaust flap cycle starts. If no error is found during the test phase, the stove enters the
preheating programme (A). This display message flashes alternately with B1 – B4.
A
1
Indicates that the Preheating Programme is running and its duration in minutes (which is variable).
The stove begins to feed pellets into the firebox, the ignition element starts, and the ignition process is monitored (after
successful completion of the preheating phase the stove enters the heating programme (H); example: A1 minute 1 of
preheating programme; A8 minute 8 of preheating programme…
AI
...
Preheating programme in + number of minutes (flashes alternately with G OFF)
The stove is still in G OFF. However, the stove has registered that the I/O key has been pressed again. It is indicating that it will
automatically resume operation in x minutes (after completion of G OFF). example: AI 11 = preheating will start in 11 minutes.
H
... Heating programme + set thermal output in kW
The stove is in heating mode, example: H 8.0 = heating programme running at 8 kW.
H.M
3.0
Heating programme internal minimum + thermal output in kW
Î The heat generated by the stove is not being fed into the heating system / is not required. Thermal output has been reduced
to a minimum (3 kW) by an internal controller because boiler water temperature TW > 80°C. The stove will re-enter the heating
programme (H) when the temperature has dropped sufficiently. Note: Don’t confuse H.M (internal) with HM (no dot – external).
R
-15
Cleaning programme (R) + remaining number of minutes (flashes alternately with G OFF)
After 4 hours continuous operation the stove starts an automatic cleaning cycle of 15 minutes duration. First the stove switches
to fan after-run (R-15 and G OFF flash alternately), then the ash is removed. Note: The stove restarts automatically after
completion of the cleaning programme R.
G
OFF
Fan after-run (=stove switches off and ash is removed; 15 minutes duration)
The fan runs for another 15 minutes (the remaining pellets burn down, the flue gas is carried off, ash is removed).
Note: Only when G OFF does not flash alternately with R, AI, HE OFF or TW OFF does the stove go into standby when fan
after-run is over. In all other cases the stove restarts automatically after fan after-run is over.
TW
OFF
Heat exchanger is cut off by a thermal switch (Î heat is not fed into the heating system)
The stove switches off via an internal control mechanism because boiler water temperature TW > 85 °C. The stove restarts
automatically after the temperature has dropped sufficiently.
RA
... Cleaning prompt (appears briefly)
The stove needs cleaning; example: RA 0.1 = cleaning overdue since 0.1 t pellets.
WA
... Service prompt (appears briefly)
The stove needs servicing. example: RA 0.1 = servicing overdue since 0.1 t pellets.
PL
AUF
Fuel hopper open
The hinged cover of the fuel hopper is open. If it is open for longer than 3 minutes without interruption while the stove is in
operation (display shows Test, A, H, HM, H.M, HE, G OFF), this will produce an error shutdown (PL Err).
AL
AUF
Ashpit door open
The ashpit door is open in standby mode. If it is open for longer than 3 minutes without interruption while the stove is running
(display shows Test, A, H, HM, H.M, HE, G OFF), this will immediately cause an error shutdown (AL Err).
Only open the ashpit door when the stove is not running!
FT
AUF
Firedoor open
The firedoor is open in standby mode. If the firedoor is opened while the stove is in operation (display shows Test, A, H, HM,
H.M, HE, G OFF), the stove will immediately produce an error shutdown (FT Err).
Only open the firedoor when the stove is not running!
PE
res
Fuel level below reserve line
The fuel hopper is almost empty and should be refilled immediately. If the display message PE res appears for longer than 5
minutes the stove will produce an error shutdown (PE Err).
“Function currently not available”
This display message appears when the function you have called up is currently not available (e.g. switching off the appliance
while an automatic routine such as grate cycle/ash removal is still running.
HE
...
Externally controlled heating programme (only possible with external modulating controller)
The stove is being operated at the indicated output level via an external modulating controller;
example: HE 7.2 = heating programme running at 7.2 kW via an external controller
HM
3.0
Heating programme running at minimum level (only possible with external controller)
The stove has been set to its minimum output level (3 kW) via an external controller (MIN/MAX input).
Note: Don’t confuse H.M (dot between H and M – internal) with HM (no dot – external).
HE
OFF Heating programme switched off via external controller (only possible with external controller)
The stove has been switched off via an external controller (via input ON/OFF or BUS or TC1).
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Ivo.tec S5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Ivo.tec S5 in the language / languages: English as an attachment in your email.

The manual is 0.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Ivo.tec S5

Wodtke Ivo.tec S5 User Manual - German - 80 pages

Wodtke Ivo.tec S5 User Manual - French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info