813100
15
Zoom out
Zoom in
Previous page
1/64
Next page
© wodtke GmbH - Tübingen. IR_BA_190726 Page 15 / 64
ENGLISH
Operation Settings
3.1 Toughened safety glass plate
! Material losses
Never operate the appliance when the toughened
safety glass is damaged.
The front of the appliance is made of 6mm thick toughened
safety glass.
If damaged, the safety glass will shatter into many small pieces
with blunt edges to minimise any risk of injury. On very rare
occasions, safety glass can spontaneously break even without
external inuences.
- Avoid any strain on the glass plate, e.g.caused by people
or objects leaning on it.
- When selecting an installation site, ensure that no persons
or objects can come to harm if the toughened safety glass
spontaneously breaks.
Note
Due to the manufacturing process for safety glass
(ESG), chemical and mechanical variations in the
surface quality are unavoidable. Minor atness devi-
ations, round or linear inclusions, small bubbles and
roller wave distortion may occur and do not constitute
grounds for complaint.
4. Settings
CAUTION Burns
When pressing the ON/OFF switch, avoid any con-
tact with the potentially hot glass plate.
Note
Depending on the size and design of the appliance, it
may take some time for it to reach its operating tem-
perature.
Note
When the appliance is rst commissioned, it may give
o an odour temporarily.
Ensure that the room is adequately ventilated
(with a partially open window, forexample).
The ON/OFF switch is located on the outer edge of the appli-
ance.
D0000055943
1
1 ON/OFF switch
Switch the appliance on or o using the ON/OFF switch.
The appliance is controlled exclusively via external room tem-
perature controllers.
Observe the operating and installation instructions of the
connected room thermostat.
5. Cleaning, care and maintenance
- After it has cooled down, clean the appliance with a damp
cloth and, if necessary, commercial glass cleaner.
- Never use any abrasive or corrosive cleaning products.
6. Troubleshooting
Problem Cause Remedy
The appliance
does not heat
up.
Fuse or safety switch
has blown/tripped.
Check the respective fuses and
safety switches.
Remove the cause.
Overheating. The high
limit safety cut-out has
tripped.
Remove the cause. The appli-
ance restarts after it has cooled
down for a few minutes.
If you cannot remedy the fault, contact your qualied con-
tractor. To facilitate and speed up your request, provide the
number from the type plate (000000-000000).
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Feel Warm IR300- IR500 - IR700 - IR900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Feel Warm IR300- IR500 - IR700 - IR900 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9.26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info