813070
29
Zoom out
Zoom in
Previous page
1/83
Next page
Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc Page 29 / 83
© wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue xx/2007 Art. No. 950 281
6.1 Output of On/Off signals or collective error messages (relay table)
As can be seen from the above table, relay outputs R1, R2 and R4 are switched depending on
the operating state or error status of the appliance. This feature can be used to forward
messages from the wodtke appliance to an external controller or a modem, permitting remote
sampling of functional values, for example. In this case operating states and collective errors
are defined as follows.
Note:
15-minute fan after-run “G OFF” counts as operating time.
Relays R1 and R2 are designed as make-contact (not break-contact) relays (i.e. closed
when operated).
Relay R4 is designed as a break-contact relay (potential-free, 2 A maximum load).
R1 = On/Off signa:
R1 = 0 V = stove off message “R1 OFF”
R1 = 230 V = in operation message “R1 ON”
R2 = collective error message
R2 = 0 V = error message “R2 OFF”
R2 = 230 V = no error message “R2 ON”
R4 = potential-free On/Off signal (monitored break-contact safety relay):
R4 = closed = stove off message “R4 OFF”
R4 = open = in operation message “R4 ON”
Matrix of operating
states Normal
operation Operating error “Off” via external
controller
without error
“Off” via external
controller
with error
“Off” via
operating panel
and therefore not
ready for
operation or
power failure
State of I/O key on
operating panel ON
=
ready for
operation
ON
=
ready for operation
ON
=
ready for operation
ON
=
ready for
operation
OFF
= not ready for
operation
State of external
controller HE at
“ON/OFF” input (if
connected)
ON
or bridged ON
or bridged
OFF
(message
“HE OFF”)
OFF
(message
“HE OFF”) Either ON or OFF
An error has occurred
or the appliance is not
ready for operation NO YES NO YES Either YES or NO,
since not ready for
operation = error
Voltage at outp
ut R1
230 V
230 V
0 V
0 V
0 V
Voltage at output R2
230 V
0 V
230 V
0 V
0 V
State
of R4 (break-contact
relay)
open
open
closed
closed
closed
Note:
I/O key on the operating panel overrides all other controls = “heater emergency switch”
for the pellet stove.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke CW 21 Airplus S4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke CW 21 Airplus S4 in the language / languages: English as an attachment in your email.

The manual is 3.18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke CW 21 Airplus S4

Wodtke CW 21 Airplus S4 User Manual - German - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info