813056
49
Zoom out
Zoom in
Previous page
1/68
Next page
Manual_S5_Airplus_2015_04_20 Page 49 / 68
© Wodtke GmbH - Tübingen. All Rights and Changes Reserved.Printed 04/2015 Part No. 950 976
Work on the air intake pipes and the aluminium
flex hoses in the furnace may only be performed
by a qualified installer, as improper procedures
can negatively influence the seal tightness of the
furnace. The aluminium flex hoses may not be
damaged, as this would result in leaks and mal-
functions.
The assembly is carried out in reverse sequence.
After assembly, be sure to verify that all connec-
tions are completely sealed!
After completing the maintenance work, carry out
a brief function test of the air volume sensor.
Open door while furnace is operating (furnace
must have been in operation for at least 1 minute).
The furnace display must show the indicator "L-
LO" (lack of air) within 20 seconds after opening
the door. After closing the door, this indicator must
disappear immediately. Note: Do not hold the door
open for longer than 1 minute, as otherwise a fault
shut-down will occur.
16.8 Inspection of Seals and Me-
chanical and Electrical Com-
ponents
Inspect all seals on the unit and replace if worn.
Visually inspect the installation of the electrical
cables. In particular, cables may not be in-
stalled over sharp edges or hot spots and
may not have cracks / blank spots. Replace
cables in case of breakage, cracks, etc. Carefully
dust electrical components with a paint brush in
case of heavy dust contamination and clean elec-
trical contacts with scratches or the like of corro-
sion residue and apply contact spray.
16.9 Inspection and Cleaning of
Convection Air Routing
It is recommended that all convection air spaces
(including under the side panelling and between
the guide plates) be inspected once per year and
cleaned with a vacuum cleaner or paint brush in
case of heavy dust contamination.
16.10 Inspection and Cleaning of
Pellet Chute
The pellet chute from the storage container to the
burner pot must be thoroughly cleaned of residue
(especially tar or dust encrustations, pellet resi-
due, burned-in pellet residue) with a wire brush or
the like so that the chute is smooth, pellets slide
properly into the burner pot and only a small
amount of dust remains on the chute.
Fig. 94: Pellet chute
16.11 Inspect and Lubricate Moving
Parts
Moving parts, such as door hinges, door locks, etc.
must be inspected for ease of movement and lu-
bricated as applicable.
Use only highly heat resistant oil (e.g. Neoval
spray, wodtke part no. 000 945) or copper paste.
Attention: Never spray oil while furnace is hot
or firing; allow furnace to completely cool
first!
Pellet chute
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wodtke Crazy.nrg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wodtke Crazy.nrg in the language / languages: English as an attachment in your email.

The manual is 6.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Wodtke Crazy.nrg

Wodtke Crazy.nrg Usermanual and installation guide - German - 72 pages

Wodtke Crazy.nrg User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info