603169
6
Zoom out
Zoom in
Previous page
1/16
Next page
Cable installation:
Connect the control cable and power cable to the back of the TRAV’LER Interface box as shown below. Note:
For cable runs longer than 25’ an extension may be purchased. Do not exceed 50’ of cable.
Attach the TRAV’LER control cable to the TRAV’LER Interface Box, as shown in Figure 5.
Attach the output cable from the Power supply to the TRAV’LER Interface Box. See above.
Finally, connect a coax cable from the TRAV’LER mount to each of the receivers being used with the TRAV’LER
Automatic Satellite Dish. See Appendix for information on properly installing a Hex Connector.
Find a location to plug in the TRAV’LER Power supply and plug it in.
Reector Installation:
Once the wires are run and the sealant has started to cure:
Check to be sure that there is nothing above the TRAV’LER that might prevent it from raising. You will need at
least 40” of clearance above the TRAV’LER Mount to ensure that you have room to install the reector.
Steps 1-7 explain how to use the TRAV’LER Interface box to raise the mount to install the reector.
1. Press [POWER] and hold for 1 second to turn “ON” the TRAV’LER Interface Box. Wait until
the Interface Box nishes “connecting to antenna”.
UPDATE: You have “10 SECONDS” to do Step 2 or, the “Search Routine” starts. (See NOTE)
2. Press [ENTER] and hold for 2 seconds or until the unit enters its Menu Mode.
3. Press [SELECT] to move the asterisk to [INSTALLATION].
4. Press [ENTER]. You will be asked to provide a code to enter the Installation Menu.
5. Press [ENTER] 4 times to enter code 0000.
6. Press [SELECT] to move the asterisk to [RAISE DISH].
7. Press [ENTER] the TRAV’LER mount will raise up about half way, to make it possible to attach
the reector.
NOTE: If the TRAVLER enters the Search Routine you can still enter the Menu Mode. See steps A & B.
If the TRAV’LER Mount rises past 1/2 way before [RAISE DISH] is selected (See Step 6) the
TRAV’LER will hit its Upper Hard Stop and “Motor Stall” appears. This is Normal!
The “Motor Stall” means the TRAV’LER is all the way up & mount can rise no more. There are
two easy ways to clear the “Motor Stall”. Either is okay. (See Steps A & B).
A. Press [ENTER] the TRAV’LER will return to the “Installation Menu” or
B. Press [POWER] the TRAV’LER will stow and turn “OFF” (Restart at Step 1).
FIGURE 5
Power
Control Cable
`
`
6
FIGURE 5
INSTALLATION
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Winegard SK-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Winegard SK-1000 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info