745748

Wiking Atomic Manual

27
Zoom out
Zoom in
Previous page
1/52
Next page
27
English
Lighting and Firing your WIKING Wood-Burning Stove
The rst ring
The rst time you re your wood-burning stove, you must do so carefully, as all materials
need to adjust to the heat. This means that the stove must be heated slowly, until it reaches
its maximum heat level. Afterwards, you should re a few times so that the stove is thoroughly
heated throughout.
Be Careful of the Lacquer
The lacquer used to treat the wood-burning stove will harden the rst 2-3 times the stove is
red, and this can create unpleasant smoke and odours. Ensure therefore that the room is well
ventilated. The door must also be carefully opened; otherwise there is a risk that the seals will
stick to the lacquer.
Warning: The enclosed gloves can scratch the surface paint if the lacquer has not hardened pro-
perly. Be careful not to touch the lacquered surfaces until after the rst 2-3 rings.
Lighting
1. The damper is completely opened by pulling the lever beneath the door 20 mm towards you.
2. Stack 8-10 nely split pieces of rewood, corresponding to 1-2 kg, inside the wood-burning stove.
The smaller the sticks, the shorter the time needed for the stove to be heated and for the optimal
combustion temperature to be achieved.
3. Place two relighters between the top layer of kindling. WIKING recommends using high-quality
relighters, as they do not produce smoke or odours.
4. Light the relighters. Keep the door ajar for a couple of minutes until the glass is hot - this pre-
vents condensation. Then close the door completely.
5. When the rewood is fully ignited, push the air damper in 10 mm so that it is halfway in. This
creates even and steady combustion.
Warning: The door may only be kept open when lighting, adding rewood or cleaning the
wood-burning stove; otherwise combustion becomes too powerful, which in turn increases the
risk of the stove becoming overheated.
Firing (Adding Firewood)
When there are no more visible ames and only a solid layer of embers remains, more fuel
can be added to the re.
1. Carefully open the door to prevent smoke and embers from escaping.
2. Lay 2-4 pieces of split rewood (approximately 2 kg) on top of the embers.
3. Close the door again and open the damper completely by pulling the lever towards yourself.
4. After a short while the ames should are up again. When the rewood is fully ignited, push the
damper 10 mm in, depending on how much heat you want. The further in your push the lever, the
less heat produced by the stove.
Warning: During combustion, the stove’s surfaces and door become extremely hot - exercise
great caution.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wiking Atomic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wiking Atomic in the language / languages: English, German, Italian as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info