757682
13
Zoom out
Zoom in
Previous page
1/16
Next page
13
PROBLEM POSSIBLE CAUSE SOLUTION
The cycle starts (buttons
flash) but the pump does
not work. Overheating.
Switch the machine off and wait
for approximately 15 minutes
before switching back on again.
If the problem persists when the
machine is switched back on
again, call the after sales service.
The machine does not
switch on No power supply.
Check electrical connection. If
the problem persists when the
machine is switched back on
again, call the after sales service.
Insufficient vacuum in bag
1. Irregular or insufficient seal on
bag.
2. Irregular sealing strip.
3. Bag dirty or burst.
4. Bag of unsuitable size for the
product contained inside.
5. Poor pump performance.
1. Position the bag correctly.
2. Check the state of the teflon
covering.
3. Change bag.
4. Select a bag in which the
product does not exceed 2/3 the
volume.
If the problem persists when the
machine is switched back on
again, call the after sales service
The machine does not seal
the bags.
1. Dirty contacts.
2. Sealing bar element broken.
3. No power supply.
Release the sealing bar from its
two pins and, clean the two holes
on the bar.
If the problem persists when the
machine is switched back on
again, call the after sales service.
The packaging machine
is off No electrical power or electronic
fault.
Disconnect the electrical power
supply.
Contact the technical support
service.
The keys do not react to
the commands. The surface of the control panel
is dirty or wet. Clean and dry the surface of the
control panel.
The lid doesn’t open.
A cycle is running.
There is no indicator light
illuminated on the panel
It is normal that during the
operating cycles the lid remains
closed. Wait for the end of the
cycle or press STOP to interrupt
the cycle and emptythe tray.
During the cycle there is no
electrical power. Restore the
power supply and wait for
decompression of the tray.
Too much air remains in
the sealed bag.
The bag is not suitable to the
dimensions of the product to be
packaged.
The level of vacuum chosen is
too low.
The product is liquid.
Use a bag of suitable size.
Repeat the cycle with a higher
level of vacuum.
It is normal that with a liquid
product, some air bubbles remain
inside.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool W11SVD140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool W11SVD140 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool W11SVD140

Whirlpool W11SVD140 User Manual - German - 16 pages

Whirlpool W11SVD140 User Manual - Dutch - 16 pages

Whirlpool W11SVD140 User Manual - French - 16 pages

Whirlpool W11SVD140 Installation Guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info