607067
6
Zoom out
Zoom in
Previous page
1/54
Next page
6
discarded.
Move the appliance without
lifting it by the worktop.
Connect the water inlet
hose(s) to the water supply
in accordance with the
regulations of your local water
company.
For models dedicated only for
cold water: Do not connect to
the hot water supply.
For models with hot ll: the
hot water inlet temperature
must not exceed 60 °C.
Make sure that the ventilation
openings in the base of
your washing machine (if
available on your model) are
not obstructed by a carpet or
other material.
The supply water pressure
must be in range 0.1-1 MPa.
If you want to place a dryer
on top of your washing
machine, rst contact our
After-Sales Service or your
specialist dealer to verify if
this is possible. This is only
admitted if the dryer is xed
on the washing machine by
using an appropriate stacking
kit available through our After-
Sales Service or your specialist
dealer.
ELECTRICAL WARNINGS
Make sure the voltage
specied on the rating plate
corresponds to that of your
home.
This washing machine is
exclusively destined to treat
machine washable laundry in
quantities which are usual for
private households.
INSTALLATION
Installation and repairs must
be carried out by a qualied
technician, in compliance
with the manufacturer’s
instructions and local safety
regulations. Do not repair
or replace any part of the
appliance unless specically
stated in the user manual.
Use protective gloves to
perform all unpacking and
installation operations.
The appliance must be
disconnected from the power
supply before carrying out any
installation operation.
Only activate the appliance
when the installation
procedure has been
completed.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest
After-sales Service.
During installation, make
sure the appliance does not
damage the power cable.
The appliance must be
handled and installed by two
or more persons.
When installing the appliance
make sure that the four feet
are stable and resting on
the oor, adjusting them as
required, and check that the
appliance is perfectly level
using a spirit level.
Remove the bottom
protection by tilting and
turning the washing machine
on one rear bottom corner.
Make sure that the plastic
part of the bottom protection
(if available on the model)
remains in the packing and
not in the machine bottom.
This is important, as otherwise
the plastic part could damage
the washing machine during
operation.
If the appliance was exposed
to the cold prior to delivery,
keep it at room temperature
for a few hours before
operating.
Do not install your appliance
where it may be exposed to
extreme conditions, such as:
poor ventilation, temperature
below 5°C or above 35°C.
In case of wooden or so-called
“oating oors” (for instance
certain parquet or laminate
oors), place the appliance
on a sheet of plywood at least
60 x 60 cm wide/ deep and
at least 3 cm thick which is
secured to the oor.
Use only new hoses to connect
the appliance to the water
supply. Used hoses must
not be used and should be
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool FSCR 10420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool FSCR 10420 in the language / languages: English as an attachment in your email.

The manual is 6,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool FSCR 10420

Whirlpool FSCR 10420 Quick start guide - English - 8 pages

Whirlpool FSCR 10420 Quick start guide - German - 8 pages

Whirlpool FSCR 10420 Usermanual and installation guide - German - 54 pages

Whirlpool FSCR 10420 Quick start guide - Dutch - 8 pages

Whirlpool FSCR 10420 Usermanual and installation guide - Dutch - 54 pages

Whirlpool FSCR 10420 Quick start guide - French - 8 pages

Whirlpool FSCR 10420 User Manual - French - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info