307429
11
Zoom out
Zoom in
Previous page
1/16
Next page
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (if available) point to the source of the fault.
Fault description table
a. Water inlet fault (no water or insufficient
water pressure)
The “Water tap closed” indicator is on and the
digital display shows “FH”. Switch off the
appliance by turning the programme selector to
the “ ” position and unplug it.
Check whether:
the water tap is open and the water supply
pressure is sufficient;
the water inlet hose is kinked;
the mesh filter between the tap and the hose is
clean (see “Care And Maintenance” / “Mesh filter
in water connection”);
the water supply hose is frozen up.
Connect the appliance to the electrical supply.
Reselect the desired programme and press the
“Start/Pause”
button again to continue with
the programme (do not add detergent for this
programme)
b.Draining fault
The digital display shows “FP”. Switch off the
appliance by turning the programme selector to
the “ ” position and unplug it.
Check whether:
the drain hose is kinked (see “Installation”);
IMPORTANT
: before draining, allow the wash
water to cool down.
the drain hose is frozen.
Connect the appliance to the electrical supply.
The pump/filter is blocked (see “Removing The
Filter” / “Draining Residual Water”).
IMPORTANT:
Make sure that the washing water
has cooled before draining.
Reselect the desired programme and press the
“Start/Pause”
button again to continue with
the programme (do not add detergent for this
programme). If the fault re-occurs, contact
After-Sales Service (See “After-Sales Service”).
c. Electrical module fault
The digital display shows “F4” to “F21” or “888”.
Set the programme selector to the “
position, select the desired programme and
press the
“Start/Pause”
button again. The
programme will continue.
If the fault re-occurs, contact After-Sales
Service (See “After-Sales Service”).
d.Aquastop / Water Stop fault
An audible tone sounds. The light of the
Aquastop / Water Stop indicator goes on. The
digital display shows “FA and the pump is
running.
The Aquastop / Water Stop fault” may have
been triggered by:
too much foam.
a leak in the appliance, water running into the
water tank.
1.
Switch off the appliance by turning the
programme selector to the “ ” position,
unplug the appliance and turn off the tap.
2.
Inform After-Sales Service and describe the fault
(see “After-Sales Service”).
3.
If the “Start/Pause” button has not been pressed
but water is still running into the machine, shut
the water intake and also inform After-Sales
Service (see “After-Sales Service”).
Small lamp lights up Digital display Fault description
“Water tap closed” “FH” “Water inlet fault”
- “FP” “Draining fault”
- from “F4” to “F21” or “888 “Electrical components fault”
“Aquastop / Water Stop” “FA” “Water Stop fault”
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm1001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm1001 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info