307429

Whirlpool awm1001 Manual

10
Zoom out
Zoom in
Previous page
1/16
Next page
TROUBLESHOOTING GUIDE
This washing machine is equipped with automatic
safety functions which detect and diagnose faults
at an early stage and react appropriately.
Often, however, the faults detected are small
enough to be solved in a matter of minutes.
For example:
The appliance will not start; no lamp lights up.
Check whether:
•
the appliance is plugged in;
•
the wall socket is functioning correctly
(use a table lamp or similar to test);
•
a programme is selected correctly.
The appliance will not start, but the
“Start/Pause” lamp is flashing.
Check whether:
•
the appliance door is properly closed
(child lock);
•
the programme has been changed;
•
the water tap is turned on. If not, turn the tap
on and press the
“Start/Pause”
button.
The appliance stops during the programme.
Check whether:
•
the
“Rinse Hold”
lamp is on. Terminate this
option by pressing the button again;
•
another programme has been selected.
Reselect the desired programme and press the
“Start/Pause”
button;
•
The appliance safety system has been activated.
See fault description table.
Detergent and additives incorrectly washed in.
Check whether:
•
the detergent dispenser inserts are incorrectly
located (see “Care And Maintenance”);
•
enough water is being supplied. The mesh filters
in the water connection could be blocked (see
“Care And Maintenance”).
The appliance vibrates during the spin cycle.
Check whether:
•
the appliance is levelled and solidly installed on
all four feet (see “Installation”);
•
the transit bolts have been removed. Before
using the washing machine you must remove the
transit bolts (see “Installation”).
Final spin results are poor:
The appliance has an imbalance detection and
correction system. If individual heavy articles are
loaded (bathmat, bathrobe, etc.) this system may
reduce the spin speed automatically to protect the
appliance or even interrupt the spin cycle
altogether, if the imbalance is too great even after
several spin starts.
•
If the laundry is still too wet at the end of the
cycle, add other articles of laundry and repeat
the spin cycle.
•
Excessive foam formation may prevent spinning.
Ensure correct amount of detergent is used.
•
Check whether the spin speed has been reduced
to 0.
No water or insufficient water pressure for
appliances with safety hose:
•
the appliance has a safety hose and the safety
valve has opened (red indicator in the safety
valve inspection window; see “Installation”/
“Connect the water supply hose”).
In this case replace it with a new safety hose.
The programme time given on the time
remaining display “jumps” suddenly up or
down by several minutes, or the
programme duration shown at the start
increases/decreases by some time:
This is a normal adaptation action by the washing
machine to factors that can affect the duration of
the wash programme, e.g.
•
excessive foaming;
•
load imbalance from individual, heavy items of
laundry;
•
longer heating time from correspondingly cold
water supply.
Because of such influences, the time remaining in
the programme is recalculated and updated if
necessary. In addition, the washing machine
determines the amount of the load during the
filling phase and adjusts the initially indicated
programme duration appropriately if necessary.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awm1001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awm1001 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info