470485
10
Zoom out
Zoom in
Previous page
1/15
Next page
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (if available) point to the source of the fault.
Fault description table
a. No or not enough water inlet
Open the water tap and check wether the water
supply pressure is sufficient.
Remove kinks in the water supply hose.
Make sure that the room temperature is not too
low to avoid freezing up of water in the hoses.
Check and clean the mesh filter in the water tap
connection of the water supply hose.
b.Waste water is not pumped out
Switch off the washing machine by pressing
“On/Off” and unplug it.
Remove kinks in the drain hose.
Make sure the room temperature is not too low
to avoid freezing up of water in the hoses.
Clean filter and check pump (see “Draining
Residual Water”/“Cleaning The Filter”);
make sure
the water has cooled down before draining.
Plug in the appliance again, reselect the desired
programme and press
“Start (Pause)”
to continue
the wash process (do not add any more detergent).
c. Too much foam
When too much foam occurs, the washing
machine starts an automatic foam reduction
process. During this process, “Fod” appears on
the display and the countdown of the remaining
programme time is paused.
d.Water enters into the washing machine’s
Aquastop tray
An audible tone sounds; the pump is active.
Switch off the washing machine by pressing “On/
Off”, unplug it and close the water tap.
Inform After-Sales Service and describe the fault
(see “After-Sales Service”).
e.Failure of electrical component
Press and hold “Reset/Drain” for a few seconds.
Reselect the desired programme and press the
“Start (Pause)”
button to continue the
programme.
f. Door cannot lock
Press and hold “Reset/Drain” for a few seconds.
Try to close the door again.
g.Door cannot unlock
Press and hold “Reset/Drain” for a few seconds.
Try to open the door again.
If any of the faults described above persist,
switch off the washing machine, unplug it and
contact our After-Sales Service (see “After-
Sales Service”).
Indication
on display
Problem Possible origin
Remedy
See under
AH
No or not enough water
inlet.
Water tap is not open.
Water supply pressure is too low.
Water supply hose is kinked.
Water supply hose is frozen up.
Mesh filter in water inlet hose is obstructed.
a
FP
Waste water is not
pumped out.
Drain hose is kinked.
Drain hose is frozen.
The pump or filter is blocked.
b
Fod
Too much foam during
the wash programme.
Too much detergent added.
Overdosing of detergent concentrates.
c
FA
Water enters into the
Aquastop tray in the
washing machine’s
bottom.
A leak inside the washing machine.
d
F1 to F99
or FH
Failure of electrical
component.
Can be diagnosed by a qualified technician only.
e
FdL Door cannot lock.
Can be diagnosed by a qualified technician only. f
FdU Door cannot unlock.
Can be diagnosed by a qualified technician only. g
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWM 1113 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWM 1113 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWM 1113

Whirlpool AWM 1113 User Manual - German - 16 pages

Whirlpool AWM 1113 User Manual - Dutch - 16 pages

Whirlpool AWM 1113 Quick start guide - Dutch - 2 pages

Whirlpool AWM 1113 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info