335210
8
Zoom out
Zoom in
Previous page
1/8
Next page
43
INSTALLATION
ADJUSTMENT TO DIFFERENT TYPES OF GAS
If a different type of gas to the type shown on the rating plate
and on the orange sticker affixed to the top of the cooktop is
used, the cooktop must be converted to work with the new gas
type. Remove the orange sticker and affix it to the instructions
booklet, which must be retained for the lifetime of the appliance.
Use pressure regulators suitable for the gas pressures
indicated in the separate Product Description Sheet.
1. The gas nozzles must be changed by After Sales Service or
a qualified technician.
Nozzles not supplied with the appliance must be ordered
from After Sales Service.
2. Connect the cooktop to the gas shut-off valve by means of
a pipe suitable for the type of gas used, in compliance with
current local regulations.
3. Adjust the minimum setting of the taps.
Note: when liquid petroleum gas is used (G30/G31), the
minimum gas setting screws must be tightened as far as they
will go.
Replacing the injectors (see table in the enclosed
Product Description Sheet)
1. Remove grids (A).
2. Extract burners (B).
3. Using a socket spanner of the appropriate size, (C),
unscrew the injector to be replaced.
4. Replace it with the injector suitable for the new type of gas.
5. Re-assemble the injector in (D).
6. For models equipped with a triple crown burner, proceed as
shown in figure.
Remove the two screws (F) followed by the cap (G) then
replace both injectors (D) as previously described.
Replace the cap (G), ensuring the seal is properly
positioned before attempting to use the cooktop.
Before installing the cooktop, remember to affix the gas
calibration plate supplied with the injectors in such a way that
it covers the existing information relating to gas calibration
Adjusting minimum gas setting of taps
1. To ensure that the minimum setting is correctly adjusted,
remove knob (E) and proceed as follows:
tighten (-) to reduce the height of the flame;
loosen (+) to increase the height of the flame;
The adjustment must be performed with the tap in minimum gas
setting position (small flame) .
Upon completion of adjustment, reseal using sealing wax or an
equivalent material.
2. The primary air of the burners does not need to be adjusted.
3. After the adjustment of the minimum gas setting, light up
the burners and turn the knobs from max. position to
min. position to check the stability of the flame.
3gb53241b.fm5 Page 43 Friday, April 11, 2003 12:26 PM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool akm 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool akm 200 in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool akm 200

Whirlpool akm 200 Additional guide - English - 2 pages

Whirlpool akm 200 Additional guide - Dutch - 2 pages

Whirlpool akm 200 User Manual - Dutch - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info