550713
10
Zoom out
Zoom in
Previous page
1/54
Next page
GB10
Max. operation time
If the user forgets to switch the hob off, it switches off automatically after a given period of time from when the last hotplate was switched on. See the following table.
When this occurs, if the glass is hot enough, the residual heat indicator “H” appears on the corresponding zone power display.
IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.
After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.
Sugar or foods with a high sugar content damage the hob and must be immediately removed.
Salt, sugar and sand could scratch the glass surface.
Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer's instructions).
Read and follow the instructions given in the section “Instructions for use”.
Make sure there is not a power outage.
Dry the hob thoroughly after cleaning it.
If the hob cannot be switched off after using it, disconnect it from the power supply.
Before contacting the After-sales Service:
1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”.
2. Switch the appliance off and then on again it to see if the problem has been eliminated.
If the problem persists after the above checks, contact the nearest After-Sales Service.
Always specify:
a brief description of the fault;
the product type and exact model;
the Service number (the number after the word Service on the rating plate), located under the appliance (on the metal plate). The Service number is also given in the
warranty booklet;
your full address;
your telephone number.
If any repairs are required, contact an authorised After-Sales Service Centre (to ensure the use of original spare parts and correct repairs). Spare parts are available for 10
years.
Selected power Max. operation time (in hours) Selected power Max. operation time (in hours)
08 6 3
18 7 2
25 8 2
34 9 1
44 P 10 minutes
53
CLEANING
WARNING
- Do not use steam cleaners.
- Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”)
is not displayed.
TROUBLESHOOTING GUIDE
ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION
The hob switches off and after 30 seconds
emits an acoustic signal every 10 seconds.
Permanent pressure on the control zone. Water or kitchen utensils on the control
zone.
Clean the control zone.
A zone switches off and the indicator shows
the message “C82”.
Overtemperature. The internal temperature of electronic
parts is too high.
Wait for the hob to cool down before
using it again.
AFTER-SALES SERVICE
Attach here one of the two stickers giving the
product data, included in the warranty booklet.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool ACM 723 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool ACM 723 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 12,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info