813317

Westfire WF35 Manual

13
Zoom out
Zoom in
Previous page
1/32
Next page
WESTFIRE · WF35 WESTFIRE · WF35
13
UK
The first lighting of your stove
The heat-resistant paint on your stove will cure and harden the first time you light your appliance. The curing
process produces a good deal of smoke and odour, it is therefore important that the first time you light your
stove the room should be well ventilated. During the process it is important to open and close the stove door
periodically (every 30mins) during the first couple of firings therefore preventing the door seal cord around the
door from sticking and coming away from the door. Once the heat-resistant paint has hardened the smell will
disappear. This stove is NOT designed to be used with the door open, the stove door must be kept closed except
when lighting the stove, adding firewood or removing ash in order to prevent flue gases from escaping. Door not
operate appliance with ash pan removed or open.
Lighting your appliance
Quality Firelighters should be used when lighting the stove. (Never use mentholated spirit, petrol or other
flammable liquids). Lighting your stove with firelighters will be more reliable and easier than using paper.
UNIQ 35 RELOAD WEIGHTS
1 HR RELOAD 2 HOUR RELOAD
WOOD (HARDWOOD LOGS) 1.2kg 1,2kg
SMOKLESS COAL BRIQUETTES (REGISTERED ONLY) N/A 1.1kg
To light your stove Wood
1. Place a few smaller pieces of dry wood (kindling) in the stove on top of the nontoxic firelighters, place one or
two small dry split (¼ split) logs on top.
2. Fully open the secondary air control above the stove door on right hand side. Fully open primary air control at
base left of stove. Pull out riddling arm fully at base right of stove (if necessary). The Uniq 35 stoves air controls
are now fully open.
3. Light the firelighters and push door to closed position and close handle to 1st position; this will allow a small
gap in the door for more air to be supplied to stove during ignition period.
4. When the flames are established and the fire is burning brightly push the door latch to position 2 fully closed.
5. Once fire is burning brightly again close the primary air control. Push in riddling arm. This will close off the
primary air to the stove. If the stove begins to falter after the primary is closed, open primary control again and
leave until fire has established, then close.
6. The fire should now be fully established and burning brightly. At this stage close secondary air control by 50%,
this is the operational setting. For the stove to burn cleanly and efficiently plenty of secondary air is needed,
do not be tempted to shut the fire down too early as this may cause smoke. At nominal heat output, expect to
refuel your stove once an hour.
The WESTFIRE UNIQ 35 stove is equipped with a manual regulating control for secondary air; this is designed to
ensure a plentiful supply of oxygen during firing. It is important therefore to not fully close the secondary air
control.
When lit, the stove will get very hot and due care must therefore be exercised. Please use a glove and operating
tool supplied when operating air controls and riddler.
RE-FUELING wood
To re-fuel your stove in the cleanest way.
Only refuel your stove when flames have died down and you have glowing embers.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Westfire WF35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Westfire WF35 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info