Manual Westfire WF32 (page 19 of 36) (English, German, Dutch, Danish, French)

813316

Zoom out

Zoom in

1/36

WESTFIRE · WF32 WESTFIRE · WF32

Only speciﬁc SE models are suitable for smoke control areas, alterations should not be attempted.

Westﬁre smoke control stoves should not be burnt with the door left open.

The refuelling procedure : - allow the newly charged fuel to burn with the secondary air control set at maximum

for up 3 to 4 minutes. After this period, with ﬂames from the logs fully established, close the secondary air supply

to the low output setting. When operating at high output (secondary air set fully open) the new refuel charge

does not require any boost air to establish combustion.

RE-FUELLING WHEN BURNING WOOD

BURNING WOOD IN A SMOKE CONTROL AREA

To re-fuel your stove in the cleanest way only refuel your stove when ﬂames have died down and you have

glowing embers. Before refuelling, open air controls fully and slide. Unlatch door to equalise pressure with the

room. Open door gently, add one piece of wood WESTFIRE UNIQ32 and close the door. Once the ﬂames from the

logs are fully established move air control to nominal position. The stove is only suitable for intermittent use only:

do not run overnight or for long periods unattended.

Experience will determine the settings that produce best results. Use a ﬂue thermostat to check the stove is not

overheating. Flue thermostats should be placed directly above collar of the stove on a non insulated section of

pipe. (efﬁcient operating temperature range is between 200c and 400c?)

SE MODELS – smoke exemption modiﬁcation

Smoke exempt models are factory ﬁtted with a air stop on the air control slider:

Refuelling on to a low ﬁre bed

If there is insufﬁcient burning material in the ﬁrebed to light a new fuel charge, excessive smoke emission can

occur. Refuelling must be carried out onto a sufﬁcient quantity of glowing embers and ash that the new fuel

charge will ignite in a reasonable period. If there are too few embers in the ﬁre bed, add suitable kindling to

prevent excessive smoke.

Operation with door left open

Operation with the door open can cause excess smoke. The appliance must not be operated with the appliance

door left open except as directed in the instructions.

Dampers left open

Operation with the air controls or appliance dampers open can cause excess smoke. The appliance must not be

operated with air controls, appliance dampers or door left open except as directed in the instructions.

Fuel Overloading

The maximum amount of fuel speciﬁed in this manual should not be exceeded, overloading can cause excess

smoke.

Annual service

The inside of the stove should be serviced /cleaned once a year. To clean the inside, remove all ash, soot and tar

residue from the combustion chamber. Remove insulated chamber panels and bafﬂe, to clean out any dirt and

soot will collected behind them. Check the quality of all insulated panels and replace any which are damaged or

cracked, replace stove door rope cord in the door. Check glass is correctly positioned.

The stove, the ﬂue pipe connection and the chimney should be checked regularly by a qualiﬁed engineer. The

chimney should also be checked for blockages before relighting the stove if it has not been used for an extended

period of time.

Stove Log length & weight

WF32 4 pieces approx 22 cm, 2.1 kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Westfire WF32 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 2.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Westfire WF32 Manual

Product: