813316

Westfire WF32 Manual

9
Zoom out
Zoom in
Previous page
1/36
Next page
WESTFIRE · WF32 WESTFIRE · WF32
9
UK
These instructions cover the basic principles to ensure the satisfactory installation of the WESTFIRE WF32/
UNIQ 32 inset wood stove, although detail may need slight modification to suit particular local site conditions.
In all cases the installation must comply with current Building Regulations, Local Authority Byelaws and other
specifications or regulations as they affect the installation of the stove.
It should be noted that the Building Regulations requirements may be met by adopting the relevant recom-
mendations given in British Standards BS 8303, BSEN15287 as an alternative means to achieve an equivalent
level of performance to that obtained following the guidance given in Approved Document J.
STOVE PERFORMANCE & TESTING
The WESTFIRE WF32/UNIQ32 insets have been approved in accordance with EN 13240.
Nominal heat output
Stove model Weight Wood Smokeless fuels
WF32/UNIQ32 INSET 112 kg 7.0 KW N/A
PREPARATORY WORK AND SAFETY CHECKS – IMPORTANT WARNING
This stove must not be installed into a chimney that serves any other heating appliance.
There must not be an extractor fan fitted in the same room as the stove as this can cause the stove to emit fumes
into the room.
Chimney – Chimney Connection – Flue Diameter 125 mm
In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure an adequate
draught so as to clear the products of combustion and prevent smoke problems into the room.
IMPORTANT: Once the stove is unpacked and checked it is necessary to remove the central bar from the flue collar of
the stove before installation. To remove unbolt collar remove bar and replace collar.
WF32/UNIQ32 INSET
Tested Draft 12pa
Max Draft 25pa
Flue gas temperature 317°C
Flue gas flow 7.7 g/sec
NOTE: The outlet from the chimney should be above the roof of the building in accordance with the provisions of
Building Regulations Approved Document J. If installation is into an existing chimney, then it must be sound and
have no cracks or other faults which might allow fumes into the house. Older properties, especially, may have
chimney faults or the cross section may be too large. Westfire Aps recommend the use of a solid fuel flue lining
system for all installation into existing chimneys. All chimney systems must be used in accordance with Building
Regulations Approved Document J.
If there is no existing chimney then either a prefabricated block chimney in accordance with Building Regula-
tions Approved Document J or a twin walled insulated stainless steel flue to BS 1856-1. These chimneys must be
fitted in accordance with the manufacturer’s instructions and Building Regulations. A single wall metal flue pipe is
suitable for connecting the stove to the chimney but is not suitable for using for the complete chimney. The con-
necting flue pipe must have a minimum diameter of 125 mm and its dimension should be not less than the size
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Westfire WF32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Westfire WF32 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 2.22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info