683224
34
Zoom out
Zoom in
Previous page
1/45
Next page
1. Attach the screw that you saved from the HDD you removed, then attach the
plastic tray that was included and designed for the My Book Duo device.
Attach the screw as is illustrated in Figure 8.2 before attaching the plastic
tray.
Next, attach the plastic hard drive tray, which fits on the underside or circuit
board side of the hard drive.
The end of the tray that is closed and has the latch, must be on the side of
the hard drive with the narrow serial number barcode label.
As is illustrated in Figure 8.2, insert the drive into the
non-flexible part of the
tray
first so that the pins fit snugly.
Next, gently flex the opposite end of the plastic tray so that the tiny pins on
the insides of the tray go into the holes on the side of the hard drive. Make
sure the pins remain
firmly connected to the tray – the pins may become
dislodged.
2. Once the tray is attached, slide the drive into the My Book Duo device. The
drive-tray combination should slide in easily. Do not force it. If the drive does
not slide in easily, verify that the drive tray is properly attached to the drive.
Orientation Note: The side of the hard drive with the SATA connector and
power connector, must point down into the unit. The side of the hard drive
with the small serial number barcode label must face up. The latch must be
on the side of the tray that is closest to the rear panel of the unit.
The drive is completely inserted once the plastic latch connects or latches
into the metal chassis of the unit.
3. Re-attach the top cover of the My Book Duo device.
Note that one end has curved hinges that go in
first, then press down on the
other side of the lid until it is flush with the top of the My Book Duo unit.
SES Driver - What is it?
ISSUE: Windows attempts to install a driver called the
SES Driver
every time I
connect my external device to a computer. What is this driver, why is it required
and how can I get rid of the repeated prompts to install the driver?
CAUSE: Western Digital My Book devices require a special communications channel
(SCSI) when connected to a personal computer to enable certain features such as
password protection, LED control, and access to pertinent device information.
At install, the Windows operating system detects this SCSI communications
channel and attempts to install a SCSI Enclosure Services (SES) driver. This driver is
only used by the external WD device and is installed by default when the device is
first attached to the computer.
If the driver was not installed or you chose not to install the WD Discovery
software, Windows will continue to prompt you to install the driver each time the
device is connected. This will continue to occur unless the SES driver is installed.
SOLUTION: We recommend that you install the WD Discovery software to resolve
this issue. However, you can also install the SES driver independently by selecting
the "Install the software automatically" option on the Windows popup screen.
Windows will automatically
find the Windows SES driver online, install it, and the
prompting will disappear.
Troubleshooting
My Book Duo
User Manual
29
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Western Digital My Book Duo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Western Digital My Book Duo in the language / languages: English as an attachment in your email.

The manual is 6,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Western Digital My Book Duo

Western Digital My Book Duo User Manual - German - 50 pages

Western Digital My Book Duo User Manual - Dutch - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info