Manual Weller WD 2 (page 44 of 171) (All languages)

585250

Zoom out

Zoom in

1/171

Following this, the set temperature (specified value) of the

active channel is displayed for a brief period. After this, the

electronics system switches automatically to the actual

value display. The "" symbol appears and the three fixed

temperatures of temperature buttons I, II and III are display-

ed.The set temperatures for channel 1 and 2 appear in small

form in the display. The active channel is labelled with an

arrow underneath it. In addition to this, the displayed chan-

nel is labelled by a red LED next to the connection socket.

The "" symbol and the green LED on the connection sok-

ket are used as a visual control check. When lit up perma-

nently, this indicates that the system is heating up. Flashing

indicates that the service temperature has been reached.

4. Channel selection

When the channel selection button 1 or 2 is pres-

sed, the display shows the temperature actual value of the

selected channel. The channel that is active in the display is

labelled with an arrow underneath it. In addition to this, the

displayed channel is labelled by a red LED over the connec-

tion socket.

The displayed channel can be switched off by simultaneous-

ly pressing the UP and DOWN buttons (2) (3). This is confir-

med in the display with OFF.

To activate a deactivated channel, select it using the chan-

nel selection button, if necessary, and simultaneously press

the UP and DOWN buttons (2) (3) to switch it on. The actual

value appears in the display.

4.1 Temperature setting

4.1.1 Individual temperature setting

As a rule, the display (1) shows the temperature actual value

of the selected channel. When the UP or DOWN button is

pressed (2) (3), the display switches to the currently set spe-

cified value. The temperature symbol °C or °F flashes.

The specified value can now be changed by tapping or hol-

ding in the UP or DOWN button (2) (3) in the corresponding

direction. If the button is pressed permanently, the specified

value changes in fast mode.Approx. 2 seconds after the but-

ton is released, the display switches automatically back to

the actual value.

4.1.2 Temperature setting using the temperature

buttons I, II, III

The specified value for the temperature can be changed

separately for each channel by selecting three preset tempe-

rature values (fixed temperatures).

Factory setting:

I 150 °C ( 300 °F)

II 350 °C ( 662 °F)

III 380 °C (716 °F).

When the middle I-II-III button is pressed, the three fixed

temperatures are shown at the bottom of the display for

approx. 2 seconds. The arrow underneath disappears. The

buttons under the display now serve as temperature buttons

I-II-III for the displayed fixed temperatures. While the tem-

perature symbol is flashing, the temperature can be selected

with the three temperature buttons. After this, the display

switches back automatically to the actual value display.

4.1.3 Assignment of the temperature buttons I, II, III

The 3 temperature buttons I, II, III can be assigned any tem-

perature values for each channel separately.

When the middle I-II-III button is pressed, the three fixed

temperatures are shown at the bottom of the display for

approx. 2 seconds.

When the UP or DOWN button is pressed, the new tempera-

ture value is set (see 4.1.1). The temperature symbol °C or

°F flashes.Following this, press and hold in the desired tem-

perature button I, II or III. When the button is pressed, the

small display assigned to the temperature button also flas-

hes and, after 3 seconds, adopts the value of the large dis-

play. Release the temperature button again.

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Weller WD 2 in the language / languages: All languages as an attachment in your email.

The manual is 6,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Weller WD 2 Manual

Product: