Manual Weightec 348 (page 31 of 53) (English)

50963

Zoom out

Zoom in

1/53

Digit 12 + = Weight value increases : speed of motion see digit 15

- = Weight value decreases

1 = Weight value no motion : base level < 0,2 division in 0,8 sec.

2 = Weight value no motion : high level < 0,1 division in 1,8 sec.

? = A “set zero” command is received but the zero function is disabled with switch 5.

This command will not be executed.

> = A “set zero” command is received (zero track incl.) that, if executed, will

exceed the zero setting range . This command will not be executed.

= = The auto zero at power on will exceed the initial zero limits (-5%. .+15%, in not

legal mode -20%. .+80%).

The zero setting will not be executed, the previous zero value is not deleted and

may be transmitted after the command: X ? Z .

This = sign ranks prior to all other reports in this digit.

This report will be deleted as soon as zero setting is possible or by the command

X ! E 6, see “ E “ commands on page 38.

< = A “set net” command (tare to zero) is received (auto tare in setpoint commands

too) but the gross weight value is negative. This command will not be executed,

and a setpoint start with tare included will be blocked . See digit 4 also.

Not executable zero and tare commands stay active until execution is possible, or

are deleted after the receipt of another command.

Digit 13 = Status of the setpoints, see table 6, page 44.

Digit 14 = Decimal point and scale division multiplication factor, as selected with

switch 53 t/m 56.

The multiplication factor is integrated already in the transmitted weight value.

However the position of the decimal point should be derived from digit 14, see

table 3 on page 41.

Digit 15 = Speed of the in- or decrease of the weight value in divisions per second

(0 . . 58 d/sec.). See table 9 on page 47.

Digit 16 = End of string code: Carriage Return.

9.2 DATA STRING: A / D VALUE REQUEST with:

digit: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

data: X # A + 2 . 0 0 0 . 0 0 0 S 2 CR

Function : With this special command the rough output of the A/D converter may be requested

for.

Neither zero, tare nor divisions multiplication factor is accounted in this figure.

This 21 bits value corresponds direct with the actual loadcell signal at the input.

That means that with a 2 mV/V signal on the input, the A/D value will be 2,000,000.

So this figure may be interpreted too as the real loadcell signal, expressed in mV/V,

with a accuracy of 1 nano Volt ( = 0,000.000.001 Volt)

Digit 3 : Code A identifies this string as the A/D value from a 348

Digit 4 t/m 13 : Measured value 21 bit

Digit 14, 15 : No motion level S 1 or (high) S 2

manual 348-2 V 3.1 Page 31 01-06-2007

X ? S @ CR

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Weightec 348 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Weightec 348

Weightec 348 User Manual - Dutch - 49 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Weightec 348 Manual

Product: