50963
8
Zoom out
Zoom in
Previous page
1/53
Next page
2.6 SETPOINT FILTERS
Via setpoint start command : - Inflight filter, for the setpoint comparison only, accelerates continuous and
automatically the cut off of the setpoints, controlled by continuous measuring
of the speed of the weight increase.
Resulting in a decrease of overshoot risks at high speed dosing
- Impulse filter, for the setpoint comparison only, up to max 5 Hz ripple
2.7 NO MOTION DETECTOR
Principle : Continuous calculation of the averages of swingings.
Out of these averages the rate of no motion is calculated. Two levels ( high
and low) of no motion are detected. High level is used for zero setting, low level
for taring operations. The auto adaptive filter is also controlled by this
calculation.
At “stand still” the adaptive filter suppresses the swingings around the
calculated no motion weight value.
2.8 ZERO SETTING switch 5: ON = automatic zero setting at switching on: “auto zero”
Range at “switching on” : - In legal mode: - 5% . .+ 15% of the nett weighing capacity (overload setting)
- In not legal mode: - 20% . .+ 80% of the nett weighing capacity (overload)
Range at “in operation” - 1.3% . . . + 2.7% of the nett weighing capacity (overload setting)
Lock up : If the zero value is outside the ranges, no zero setting will be executed.
In character 12 of the data string a warning is sent. The internal display shows
a: Z .. . De last used zero value may be requested from the 348 for checking,
with the string: X ? Z .
Manual zero setting : set switch 5 off / on
External zero setting : with command via data input: X ! Z CR
Delete zero memory : set switch 4 and 5 both off, the zero track will be deleted too
2.9 ZERO TRACK switch 4: ON = continuous automatic zero setting
Range : - 1.3% . . . + 2.7% of the nett weighing capacity (overload setting)
Principle : Small deviations from the gross or net zero, < 0.5 scale division and
not faster than 0.5 division per second, will be reset to zero automatically
2.10 CALIBRATION DISPLAY
Design : Internal 2- lines dot matrix LCD display with back lightning
Reading : - gross en net weight values with x 10 improved accuracy
- status indications as : no motion, taring or zero setting in operation
- error messages
- basic info during start up procedure as : serial nr, checksum, AD value,
loadcell excitation voltage, internal temperature etc.
Manual 348-2 V 3.1 Page 8 01-06-2007
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Weightec 348 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Weightec 348 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Weightec 348

Weightec 348 User Manual - Dutch - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info