Note: It is important that all burner control knobs be in
the oposition before you turn on the LPG cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
onposition depending on your regulator/cylinder
connection.
4) Begin with burner 1, furthest to the left. Put match in
the matchstick holder and strike match. (Matchstick
holder is located under left side table.) Insert lit
match down through the cooking grates, past the
FLAVORIZER BARS and next to the burner(A).
5) Push the burner control knob in and turn it anti-
clockwise to the start/high position.
6) Check that the burner is lit by looking through the
cooking grates and through the FLAVORIZER bars.
7) If the burner does not ignite within 4 seconds,
turn burner control knob to the o position and
wait five minutes to allow the gas to clear before
attempting to light the burner again. If repeated
attempts fail, follow the gas flow troubleshooting
instructions on the next page.
8) If the burner ignites, the problem lies in the ignition
system. Follow the instructions for “Checking the
Components of the Electronic Ignition System”.
9) After burner 1 ignites, you can turn on burner 2
(and burner 3).
10) Replace the matchstick holder by hanging
underneath the left side table (B).
Checking the Components of the
Electronic Ignition System
When pressing the ignition button you should hear a
ticking sound. If you cannot hear the ticking sound,
check the battery, then check the wires.
Checking the Battery
There are three potential issues with the battery that
supplies the power to your ignition module that need
to be checked:
1) Some batteries have a plastic protective wrap
around them. (Do not confuse this plastic with
the battery label.) Check that this plastic wrap is
removed.
2) Confirm that the battery is installed correctly (C).
3) If the battery is old, replace it with a new battery.
Checking the Wires
There are two potential trouble spots that need to be
checked:
1) Check that the ignition wires are connected
securely to the terminals on the ignition button
under the control panel.
2) Make sure the ignition wires are properly attached
to the ignition module. The wire terminals are
colour coded to correspond with the terminals on
the ignition module. The number of wires will vary
per model.
A
B
C
2341
2
3
4
1
Igniter Module Wire Chart
BARBECUE WILL NOT IGNITE
SYMPTOM
• Burner does not ignite when following the electronic ignition instructions in the “Operation” section of this Owner's Manual.
CAUSESOLUTION
There is a problem with gas flow. If the barbecue will not ignite, the first step is to determine if there is gas flowing to the burners. Tocheck this,
follow the instructions below for “Using a Match to Determine if there is Gas Flow to the Burners.”
If match lighting IS NOT successful, follow the gas flow troubleshooting suggestions on the next page.
There is a problem with the electronic ignition system. If the barbecue will not ignite, the first step is to determine if there is gas flowing to the burners. Tocheck this,
followthe instructions below for “Using a Match to Determine if there is Gas Flow to the Burners.”
If match lighting IS successful, follow the instructions below for “Checking the Components of the Electronic
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Weber Spirit E220 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Weber Spirit E220 in the language / languages: English as an attachment in your email.
The manual is 13.43 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
