802209
14
Zoom out
Zoom in
Previous page
1/379
Next page
EN
2 5110757E OI II Webasto Pure
The Webasto Live charging station also meters the
plug-in cycles of the charge coupling for service
purposes and after 10,000 plug-in cycles, displays
a note on the web interface that an electrician
needs to inspect the plug contacts on the charge
coupling for any signs of wear. If any signs of
wear are discovered, the electrician must replace
the affected charging cables with genuine
Webasto spare parts.
Do not attach extension cables or adapters to the
charging cable.
Remove the charging cable by pulling on the char-
ging coupling only.
Never clean the charging station with a high-pres-
sure cleaner or similar device.
Switch off the power supply before cleaning the
charging sockets.
The charging cable must not be subjected to any
strain during use.
Ensure only persons who have read these operat-
ing instructions have access to the charging sta-
tion.
WARNING
When not in use, store the charging cable in the
designated holder and lock the charging coupling
in the remote dock. Loosely wind the charging
cable around the remote dock making sure the
cable does not touch the floor.
You must make sure that the charging cable and
coupling cannot be driven over, trapped and are
protected from all other hazards.
2.3 Safety information for installation
You must comply with the locally applicable re-
quirements regarding electrical installations, fire
protection, safety regulations, and escape routes
at the intended installation location.
Only use the supplied installation material.
When open, ESD (electrostatic discharge) precau-
tions must be taken properly to avoid electrostatic
discharge.
When handling electrostatically sensitive boards,
wear grounded antistatic wrist straps and properly
observe ESD safety precautions. Wrist straps must
only be used when mounting and connecting the
loading unit. Wrist straps must never be worn on
a live Webasto Pure.
Electricians must be properly grounded during in-
stallation of the Webasto Pure.
Do not install the Webasto Pure in an explosion
sensitive area (Ex Zone).
Install the Webasto Pure in such a way that the
charging cable does not block any passageways.
Do not install the Webasto Pure in areas subject to
ammonia or air containing ammonia.
Do not install the Webasto Pure in a location
where falling objects may damage the it.
The Webasto Pure is suitable for use indoors as
well as outdoors.
Do not install the Webasto Pure in the vicinity of
water jets, such as car-wash installations, high-
pressure cleaners or garden hoses.
Protect the Webasto Pure against damage caused
by sub-zero temperatures, hail or similar. We
would like to refer you to our IP protection class at
this juncture (IP54).
The Webasto Pure is suitable for use in areas
without access restrictions.
Protect the Webasto Pure from direct sunlight.
The charging current may be reduced at high tem-
peratures, or charging may be disabled com-
pletely. For the 11 kW variant the operating tem-
perature range is -30 °C to +55 °C and for the 22
kW variant from -30 °C to +45 °C.
The installation location of the Webasto Pure
should ensure that vehicles cannot inadvertently
collide with it. Protective measures must be imple-
mented if the possibility of damage cannot be
ruled out.
Do not put the Webasto Pure into operation if it
has been damaged during installation; a replace-
ment will be required.
2.4 Safety information for electrical
connection
WARNING
Comply with the nationally applicable require-
ments pertaining to electrical installations, fire
protection, safety regulations and escape routes
at the intended installation location. Observe the
applicable national installation regulations.
Each charging station must be protected with its
own line circuit breaker and residual current circuit
breaker. See Requirements at the installation loca-
tion.
Make sure that the electrical connections are de-
energised before connecting the charging station
to the power supply.
Do not connect a vehicle during initial start-up of
the charging station.
Make sure that the correct supply cable is used for
the power connection.
Do not leave the charging station unattended with
the cover open.
Change DIP-switch settings only with the power
off.
Register with the power supply company as re-
quired.
2.4.1 Safety information for electrical connection
Comply with the nationally applicable require-
ments pertaining to electrical installations, fire
protection, safety regulations and escape routes
at the intended installation location. Observe the
applicable national installation regulations.
Each charging station must be protected with its
own line circuit breaker and residual current cir-
cuit breaker. See Requirements at the installation
location.
Make sure that the electrical connections are de-
energised before connecting the charging station
to the power supply.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Webasto Pure II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Webasto Pure II in the language / languages: All languages as an attachment in your email.

The manual is 28.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info