802117
12
Zoom out
Zoom in
Previous page
1/23
Next page
9 | WebUI
12 / 23 5111232C OI-II Webasto Next_EN
D4 0= no unbalance load limit for single-phase charging.
1= unbalance load limit at 16A and D1-D3 > 20A
(for CH and AT).
D5 0= no unbalance load limit for single-phase charging.
1= unbalance load limit at 20A and D1-D3 > 25A (for D).
D6 1= TN/TT system.
0= IT system (only single-phase connection possible).
WARNING
Only a qualified electrician may adjust the settings in
the Webasto Charger Setup app.
8.8 Initial start-up
8.8.1 Safety check
Document the results of the checks and measurements carried
out during initial start-up corresponding to the applicable in-
stallation requirements and standards.
The Webasto Charger Setup app supports you with checks dur-
ing initial start-up.
The local regulations relating to operation, installation and en-
vironmental protection also apply.
8.8.2 Start-up procedure
1. Remove material residues from the connection area.
2. Check that every screw is correctly tightened and every
clamp is correctly engaged.
3. Fit the lower cover.
4. Secure the bottom cover with the mounting screws; care-
fully tighten the mounting screws to the stop. See Fig. 5.
5. Switch on power supply.
Start sequence is activated (duration up to 60 seconds).
White chase light running up and down. See Fig. 11, op-
erating status N2.
WEM000062A
Fig.11
Check initial start-up and record the measured values in the
test log. The Webasto Charger Setup app can support you
in carrying out and documenting this. An EV simulator is
used for the measurement at the charging coupling.
Simulate and test the individual operating and protection
functions with the EV simulator.
Connect the charging cable to the vehicle.
The LED changes from green (N3) to pulsing blue
(N4). See Fig. 22.
9 WebUI
The WebUI is a graphical user interface which a user can use to
interact with the system via a web browser.
The WebUI can be accessed in the browser in the following
ways:
lWith a WLAN connection to the hotspot in the wall box,
the WebUI can be accessed in the browser at the following
IP address: 172.20.0.1
lWith a WLAN or LAN connection to the router, the WebUI
can be accessed in the browser at the following IP ad-
dresses:
YYYYY (YYYYY --> IP address that has been assigned to
the wall box by the router)
https://NEXT-WSXXXXXX (WSXXXXXX - Serial No.: see
type plate)
IP-Adresse: 172.20.0.1 IP-Adresse: - https://WSNEXT-XXXXX
- Wallbox IP-Adresse
HEMS / Smart
Meter
Fig.12
Login data:
lUser name: admin
lPassword: master password (see installation documenta-
tion)
172.20.0.1 oder YYYYY oder https://NEXT-WSXXXXX
admin
Masterpasswort
Fig.13
9.1 Settings in the WebUI for DLM
The configuration of the DLM in the WebUI will be described
below. For more information see chapter10, "Dynamic Load
Management – Stand-alone mode (DLM)" on page 13.
1. Select the HEMS tab in the WebUI.
2. Enable expert mode.
3. Under Mode, select DLM with external meter activated.
4. Under Connection type select LAN or WLAN.
5. Under Safe current L1/L2/L3 select the maximum possible
current when there is no connection to the smart meter.
6. Under External Meter IP enter the IP address for the
meter assigned by the router.
7. Under External Meter Module select the meter model.
8. Under External Meter Position select including wallbox
or excluding wallbox.
9. Under Recalculation interval enter 30.
10. Under Current limit external meter enter the maximum
current.
6.
7.
8.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Webasto Next at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Webasto Next in the language / languages: English as an attachment in your email.

The manual is 16.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Webasto Next

Webasto Next User Manual - German - 24 pages

Webasto Next User Manual - Dutch - 23 pages

Webasto Next User Manual - French - 24 pages

Webasto Next User Manual - Italian - 23 pages

Webasto Next User Manual - Portuguese - 24 pages

Webasto Next User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info