802117
11
Zoom out
Zoom in
Previous page
1/23
Next page
Installation and electrical connection | 8
5111232C OI-II Webasto Next_EN 11 / 23
12. Then remove the screwdriver again and perform a tension
test to ensure that the individual wires are clamped prop-
erly and fully and no exposed copper areas are visible.
NOTE
If multiple charging stations are connected to a com-
mon main power supply point, there is a risk of over-
load.
A phase rotation must be provided and adapted to
the connection configuration of the charging stations.
See online configuration instructions:
https://charging.webasto.com/int/products/docu-
mentation
Insert the data line into the designated connection in the
connection area. See chapter4.2.4, "Control cable (Control
Pilot)" on page 6 and Fig. 3.
Remove any soiling such as insulation trimmings out of the
connection area.
Check again for firm attachment of all wires in the corres-
ponding terminal.
Next position the cable bushing in the housing lead-
through.
NOTE
Make sure there are no air gaps between the housing
and the cable bushing.
8.4.1 The electrical connection in split-phase
systems
Terminal configuration:
Supply lead Terminal block
L1 L1
L2 Neutral
Table2: Terminal configuration
DIP switch configuration: D6 = 0 (OFF)
NOTE
This terminal configuration does not define the unbal-
ance load limit.
NOTE
Supply lead: a maximum of 230V rated voltage is per-
mitted between L1 and L2.
8.5 LAN cable
For connecting the charging station to the network infrastruc-
ture at the installation location. The charging station can be
configured and controlled using this connection (prerequisite:
connection to the back end or to the local energy management
system). A CAT7 network cable is recommended. The LAN
cable must be passed through the left-hand opening in the wall
box in order to connect it to the LAN socket.
8.6 Active power increase
4
3
2
1
Fig.9
The active power control as per the rules of VDE AR-4100
should be connected as follows:
The two cables from the ripple control receiver or the floating
contact must be connected to this connector in positions 3 and
4 (see Fig. 9). The two cables can be assigned to pos. 3 and 4 in
any order (sequence) (max. cable cross section 1.5mm²).
WARNING
No voltage should be applied between terminals 3
and 4.
8.7 DIP switch settings
DANGER
High voltages.
Danger of fatal electric shock.
Ensure safe isolation from the power supply.
DIP switches determine the maximum current. The current can
be adjusted in 1A increments using the Charger Setup app up
to the maximum value that is configured by the DIP switches.
ON (1) OFF (0)
Fig.10
DIP switch left/ON = 1
DIP switch right/OFF = 0
DIP-switch factory setting:
D1 D2 D3 D4 D5 D6
Off Off Off On On On
NOTE
Changes to the DIP switch settings become active after
restarting the charging station.
D1 D2 D3 [A] Description
0 0 0 32 Factory settings
0 0 1 10
0 1 0 13
0 1 1 16
1 0 0 20
1 0 1 25
1 1 0 8
1 1 1 0 Demo mode: charging not possible
WARNING
The DIP switches must be adapted to the upstream in-
stallation by a qualified electrician prior to initial opera-
tion.
13.
14.
15.
16.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Webasto Next at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Webasto Next in the language / languages: English as an attachment in your email.

The manual is 16.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Webasto Next

Webasto Next User Manual - German - 24 pages

Webasto Next User Manual - Dutch - 23 pages

Webasto Next User Manual - French - 24 pages

Webasto Next User Manual - Italian - 23 pages

Webasto Next User Manual - Portuguese - 24 pages

Webasto Next User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info