694512

Wanders Tali Manual

20
Zoom out
Zoom in
Previous page
1/68
Next page
20
GB
Possible settings
• By pressing the SET button you can switch quickly between MAN day temperature lamp ventilator night
temperature timer MAN.
• MAN: this setting allows you to turn the ames manually higher or lower with the big-ame button or the small-ame
button .
• Day temperature (): this mode allows you to set the desired daytime temperature; the remote control set will function as
a thermostat.
• Night temperature (): this mode allows you to set the desired night temperature.
• TIMER: this mode allows you to preset 2 switch-on and 2 switch-o times per 24 hours. If the night setting is on - - -, the stove
will burn on the pilot ame.
Setting the temperature
• Select the day temperature or night temperature by briey pressing SET button .
• Now press SET button longer until the display starts ashing.
• Preset the temperature with buttons or (5 ºC is the minimum day temperature).
• Wait or press OFF button to switch back to the thermostat-controlled system.
• In order to save the batteries you are advised to reset the night-temperature until the display shows the ‘- - -‘ signal.
Setting the timer function
• Select the timer function by briey pressing SET button a few times.
• Now press the SET button longer until P1 () starts ashing.
• Set the hours with button and the minutes with button .
• Briey press SET button for the next timing.
• Once all 4 timings have been set, press OFF button to end the presetting.
Operation (standard remote control)
Igniting the re
• Open the gas turncock that is xed in the gas pipe leading to the stove.
• Press “O I” switch on the gas control block in the “I” position.
• Turn control button on the gas control block to the ON position.
• Simultaneously press buttons and on the handset. A short acoustic signal
indicates the start, and is followed by short acoustic signals (0.2 sec/signal, 1Hz.)
until the pilot ame and the chief burner are ignited. After the main burner has lit,
the ame height will automatically go to the maximum position.
Possible error messages
• Long signals (0.8 sec. signal with 0.2 sec. interval) during lighting : batteries of the receiver are almost empty. (After hearing
this signal, you can switch on the appliance for about another 10 times.)
• 5 seconds continuous signal : error message. One of the cables may not be connected, or the “O I” switch is not in the “I”
position.
• 5 short signals (0.2 sec. signal with 0.2 sec. interval) : ignition of the pilot ame and the main burner has failed. Possible
cause: air in the pilot burner pipe.
Important: If the pilot ame has gone out you must wait at least 5 MINUTES before repeating the above-
mentioned steps.
Setting the height of the ames
• After igniting the burner, the height of the ames will automatically reach the maximum position.
• Press button continuously to lower the ames and to switch o the burner (putting the re out: “STAND BY”). Press button
briey to gradually lower the ames.
• Press button to increase the ame height. Briey press button to gradually increase the ames.
• Simultaneously press button and button to turn o the rear burner.
• Simultaneously press button and button to turn on the rear burner again.
• It is not possible to have only the rear burner be lit.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Wanders Tali at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Wanders Tali in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info