Manual Wamsler DENVER (page 26 of 83) (English, German, French, Italian)

813210

Zoom out

Zoom in

1/83

Warning!

When opening the furnace chamber door, any incorrect handling or

insufficient draught may induce smoke. Always ensure that the furnace

chamber door may be opened only slowly, first just to a small extent, and

then fully after a few seconds. In addition, if you intend to put additional fuel

into the fire, before the opening of the door only there may be only ember bed

in the burning space, i.e. no flames may be visible.

Led into the burning space in correspondence with the existing conditions, the

secondary air provides for the follow-up burning of the combustible components of

in the burning space. This in fact means smoke and soot-poor burning, which

contributes to the protection of the environment. If you wish to commission the

fireplace in a transitional period, please, please first examine the chimney draught,

as it can be especially weak at high external temperatures. Towards this end, hold

a burning match in the slightly opened feeding door. If the flame is not drawn

significantly by the draught, then a so-called starting fire is to be set first. Towards

this end, burn wood chips/wool in the fireplace or the cleaning hole of the chimney.

The fire grate is to be cleaned before every kindling to ensure the proper inflow of

air for burning. The ashtray is to be emptied regularly. Should the equipment be

extremely hot, use the gloves (pic. 4). Please, be careful not to dispose glowing

materials into the waste bin.

Ensure that the ashtray should be fully pushed into the equipment.

Warning! In order to keep the air clean and safeguard the fireplace, do not exceed

the specified maximum fuel quantity, otherwise overheating may occur, which

potentially damage the equipment. Such damage is not covered with any

guarantee. Only a single layer of fuel is allowable to be prepared in the fireplace.

Try to reach lower heating performance only by decreasing the quantity of fuel, and

not by cutting the primary air supply.

1.5 Cleaning and maintenance

After the heating season, it is recommended to clean the fireplace and the flue gas

pipes carefully. Any dropping heating performance is almost always the

consequence of the strong contamination of the flues. For cleaning, the baffle plate

is to be pulled forward. This way, the flues can be cleaned from the inside or – after

removing the flue gas pipe – from above. After cleaning, the baffle plate is be

pushed back fully again.

Warning!

Following every heating season you are advised to examine the fireplace

thoroughly. If any repair or reconditioning is needed, please, contact your local

dealer in a timely manner, and specify the model number and serial number of your

equipment (as seen on the model plate). External surfaces may be maintained only

after the fireplace cooled down, and following the first commissioning. Use cold

water for cleaning, or soap, washing ingredient in extraordinary cases, then wipe it

dry. Before its first use, clean the ROBAX inspection glass with a wet and clean

cloth, and then put a few drops of glass–ceramics cleaner onto both sides of the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Wamsler DENVER in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2.28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Wamsler DENVER Manual

Product: