517972

Waeco CAM30 Manual

24
Zoom out
Zoom in
Previous page
1/120
Next page
Mounting the camera PerfectView
24
If you would like to attach the bottom camera holder with threaded screws fitted
through the construction
a
Caution!
Ensure that nuts cannot be pulled through the body shell when they are tight-
ened.
Use larger washers or metal plates if necessary.
➤ Drill Ø 5.5 mm holes at the points you have just marked.
➤ Deburr all drill holes and apply rust-protection.
➤ Place the insulating plate (fig. 3 5, page 3) where the bottom camera holder is to be
fitted.
The insulation plate serves as a seal and protects the paint.
➤ Screw the camera holder on with the M5 x 25 mm threaded screws (fig. 7 A,
page 5).
Depending on the thickness of the construction, you may require longer threaded
screws.
Fastening the camera
➤ Push the camera into the bottom camera holder.
I
Note
Remember that the LDR sensor (fig. 4 5, page 4) must face downwards so that
the picture is correctly shown on the monitor.
➤ Fasten the camera loosely using the top camera holder and the two M3 x 12 mm
screws (fig. 7 B, page 5).
I
Note
Do not tighten the two screws until you have aligned the camera (see chapter
“Checking the function and setting the camera” on page 25).
To do this you must first install and connect a monitor (see the connection dia-
gram fig. 9, page 5).
Creating a through-hole for the camera connection cable
I
Note
If possible, use available openings – such as ventilation grilles – to feed the con-
nection cables through. If there are no existing openings, you must drill a hole
with a 13 mm diameter. Check beforehand that there is sufficient room for the
drill head to come out on the other side.
➤ Drill a hole of Ø 13 mm near the camera.
➤ Deburr all drill holes that have been made in the sheet metal and apply rust-protec-
tion.
➤ Seal the duct with the sleeve (fig. 4 3, page 4).
CAM30_CAM40.book Seite 24 Donnerstag, 14. Januar 2010 5:32 17
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Waeco CAM30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Waeco CAM30 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info