766094
5
Zoom out
Zoom in
Previous page
1/10
Next page
18 19
During clipping: Reset the tension screw by a further quarter-turn, if the blades do not cut sufficiently anymore. The
blades are blunt and must be resharpened, if resetting is unsuccessful. Be careful not to overdo the clipping tension.
Slightly reset the clipping tension occasionally during clipping. Hairs can accumulate between the shear blades, if you
clip with insufficient clipping tension. This negatively influences the clipping procedure or even makes it impossible! The
shear blades must be disassembled, cleaned, oiled and reassembled according to item 4.2 if this is the case. Avoid too
high plate pressure, since this increases temperature and wear. The factory has fully adjusted shipped shears for clipping.
3.3 Correct clipper head oiling
The most frequent error cause for a non-satisfactory clipping result as well heating up of the clipper is want of lubricati-
on. A light oil film on the shear blades is essential for an optimal clipping result as well as to increase the service life of
the shear blades and machine. All other moving parts of the clipper head must also be well lubricated. Drip oil on the
shear blades and into the oil opening of the clipper head
(fig. 1 + 2) every 10 minutes, so that these do not run dry. Only use our special clipper machine oil.
3.4 Turning on/off
The slide switch has two positions (fig. 3, shows position 0)
• Position 1: Machine is turned on
• Position 0: Machine is turned off
Check the switch position before plugging in. The switch must be in position 0. Only use the slide switch for turning the
machine on and off.
4. Maintenance
Turn the machine off and pull the power supply plug before beginning maintenance work. Always disconnect the power
supply first before working on the shear blades/clipper head. Do not touch the shear blade area even if the machine is
switched off as long as the clipper is still connected to the current supply.
4.1 Cleaning
After having finished clipping wipe the oil off the machine, clipping head and shear blades with a dry cloth and remove
the hairs with a dry paintbrush or brush. Then lightly oil all parts to prevent rusting. Note that even the smallest rust
spots impair clipping considerably or even render this completely impossible.
4.2 Shear blade assembly
The shear blade set consists of a lower plate and an upper plate. When assembling the shear blades pay attention that
the correct plates lie on top of one another.
Assemble the blades as follows:
Loosen the clipper tension screw and put the clipper onto a hard surface, so that the blade fastening screws look
upwards.
Loosen the blade fastening screws and remove the two old blades.
Ensure that the new shear blades are clean. Pay particular attention to the fact that the sharpened areas are dirt-free;
it is otherwise impossible to achieve a satisfactory clipping result even with newly sharpened shear blades.
Put the new upper plate into the swing head guides and then put some drops of oil onto the sharpened areas.
Now push the new lower plate in between the released screws (fig. 4).
As soon as you have adjusted the shear blades, fixate the lower plate position and tighten the blade
fastening screws.
4.3 Resharpening the blades
Resharpening shear blades correctly is only possible with special machines and by the specialised trade. Only use sharp
shear blades. Defective blades with broken off teeth or blunt blades must be replaced.
4.4 Storing the clipper
Between clippings always keep the well-cleaned and lubricated clipper in the supplied case in a dry location, which is
not accessible to children. Do not switch the machine on, if you suspect that liquids could have entered. There is danger
of an electric shock or short-circuit. Have the machine serviced!
4.5 Cleaning the clipper head
Clean the clipper head after a few days use. Dismantle the cutter plates. Release both screws and remove
the clipper head from the drive unit. Now clean the interior of the clipper head and the other components thoroughly
with a brush and a paintbrush. Lubricate the clipper head according to 3.3 after careful assembly.
5. Repairs
5.1 Introduction
You can read up on troubleshooting measures on the next page. Only authorised technical personnel may carry out
troubleshooting measures marked with an *.
5.2 Malfunction lists
Contact an authorised service department to repair not listed malfunctions.
6. Environmental protection and disposal
The user is responsible for the appropriate disposal of the shear blades and clipper after their service
life. Observe your local pertinent regulations. Do not dispose of the appliance with domestic refuse.
As part of the EU Directive governing the disposal of electric and electronic appliances, the appliance
is accepted free of charge by local waste collection points or recycling centers. Correct disposal will
ensure environment protection and prevent a potential harmful impact on people and the environ-
ment.
18192=BA_FarmClipper4_148x210_0816.indd 18 25.08.2016 14:40:17
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Voss Proficut at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Voss Proficut in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Voss Proficut

Voss Proficut User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info