766094

Voss Proficut Manual

3
Zoom out
Zoom in
Previous page
1/10
Next page
16 17
1. Safety regulations
1.1 General information
These safety regulations contain fundamental information, which must be observed during installation, operation and
maintenance. All persons working on and with the clipper must read the operating instructions. The operating instruc-
tions must bepermanently available at the machine usage site.
1.2 Fundamental safety instructions
Observe the legal regulations on regular examinations.
Also observe the industrial safety regulations.
1.2.1 Power supply
Only insert the plug into correctly installed sockets. Defective electrical installations can cause an electric shock or a
short-circuit. Sockets should be equipped with an earth leakage circuit breaker (FI). Observe your local pertinent regu-
lations. Only carry out maintenance and cleaning tasks after pulling the plug. Never leave the machine unsupervised
when plugged in. Clipping animals is only permissible, if children are kept away from the clipping location. Do not store
your machine in reach of children!
1.2.2 Maintenance and service obligation
Never use a damaged machine for clipping. Only allow authorised technical personnel to repair the housing or defective
electrical cable.
1.2.3 Radiation
The clipper examination complies with the fundamental protection requirements according to the harmonised European
standards of the EEC Directive. EU Directive: 83/336/EEC of 03/05/1989
1.2.4 Remaining risks
Please notify us of operational dangers and risks, which do not occur when directly trimming the animals.
This also applies to endangering technical defects.
1.3 User requirements
Observe and comply with the instructions in this manual to ensure safe use of the clipper.
• The user has read and understood the operating instructions or an expert has explained the operation and
pointed out the risks.
• The user is experienced in clipping animals. Children and frail persons (without supervision) should not use the clipper.
Safety: Corresponds to EN 60335-1, EN 60335-2-8, EN 62233
The shear blade set consists of a lower plate and an upper plate (fig. 4). When assembling
the shear blades pay attention that the correct plates lie on top of one another. Assemble
the blades as follows: Loosen the clipper tension screw (fig. 5) and put the clipper onto a
hard surface, so that the blade fastening screws look upwards. Loosen the blade fastening
screws (fig. 6) and remove the two old blades. Ensure that the new shear blades are clean.
Pay particular attention to the fact that the sharpened areas are dirt-free; it is otherwise
impossible to achieve a satisfactory clipping result even with newly sharpened shear blades.
Put the new upper plate into the swing head guides and then put some drops of oil onto the
sharpened areas (fig. 7). Now push the new lower plate in between the released screws (fig.
8). It is important that the blades lie on each other in such a way that the sharpened area of
the lower plate projects over the tips of the upper plate by approximately 1.5 - 2.0 mm (fig.
8)! As soon as you have adjusted the shear blades, fixate the lower plate position and tighten
the blade fastening screws.
2. Designated use
2.1 Intended purpose
The clipper is exclusively intended for clipping cattle, horses or large dogs. Any other use, in particular on humans, is
explicitly prohibited.
2.2 Technical data
Type designation: 18192
Supply voltage: 220 – 240 V AC
Motor rating: 200 W
Frequency: 50 Hz
Dimensions (W/H/L): 80 x 62 x 295 mm
Weight without cable: 1190 g
Sound pressure level: 85 dB (A)
Strokes: 3000/ min
Protection class: II
Operating conditions
Max. ambient temperature: 0 – 40° C
Max. air humidity: 10 – 90 % (relative)
2.3 Equipment
1 clipper with clipper head, 1 set of shear blades (mounted), (100 ml), 1 screwdriver, 1 operating manual and
1 storage case
3. Initial commissioning
3.1 Inspection and operating instructions
The inappropriate use of electrical devices, in particular animal breeding devices, is dangerous! Therefore, observe the
following, accident prevention measures before starting the machine: • Never switch the machine on without properly
mounted clipping plates • The volt specification on the rating plate must correspond to the mains voltage. The machine
may only be operated with AC • Avoid any contact with the moving blades • Always pull the power supply plug out
prior to maintenance work! Do not touch the blade area, even if the machine is switched off, as long as the machine is
connected to the current supply • Always place machine on a dry surface and store in dry rooms • Avoid any contact
with a machine, which is in contact with liquids. Never clip wet animals. Liquids that have penetrated into the machine
reduce the electrical insulation. There is the imminent danger of an electric shock or short-circuit. Only clean the
machine with a dry cloth and a paint-brush or brush • A cable lying on the floor can get caught and be dangerous. Lay
the cable carefully and safely before clipping. Prevent the clipper connection cable from kinking or tangling. Ensure that
animals do not stand on the cable, walk over it or get caught. Keep the cable away from hot surfaces. Never wind the
cable around the machine. This can result in insulation damage and cable break. Examine the cable regularly for de-
fects • Set the machine switch to off (fig. 3) before pulling the plug from the mains • Do not use damaged shear blades
with broken off teeth. Only use sharp shear blades. Only use the original shear blades. • Never insert an item into an
opening of the machine. The machine noise can disturb animals. A kick or the weight of the animal can result in sub-
stantial injuries. Therefore fixate the animal sufficiently. • Animals should only be clipped, when unauthorised persons
do not have access to the clipping location • Only clip in well-ventilated rooms and never in the proximity of explosive
materials. These safety notes must be observed in all cases!
3.2 Blade adjustment with the tension screw
Adjust as follows when placing into operation:
Prior to clipping: Turn the tension screw up to the first noticeable resistance with the machine switched off. Then con-
tinue to turn the tension screw by a further 1/4 rotation.
18192=BA_FarmClipper4_148x210_0816.indd 16 25.08.2016 14:40:17
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Voss Proficut at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Voss Proficut in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Voss Proficut

Voss Proficut User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info