764117

Vonroc VC505AC Manual

7
Zoom out
Zoom in
Previous page
1/64
Next page
EN
7WWW.VONROC.COM
4. OPERATION
Switching on (Fig. A):
Do not vacuum without a Hepa filter!
1. Fully unwind the suction hose (9).
2. Connect the mains plug.
3. Press the power switch (1) into the “ ON/1”
position to start your vacuum cleaner.
Switching off (Fig. A):
Press the power switch (1) into the “ OFF/0” posi-
tion to switch off your vacuum cleaner.
Vacuuming (Fig. B, C1, C2, D)
Clean the HEPA filter (11) regularly and
after every heavy use to maintain the
suction power.
Fine dust, such as dust from cement, soot
and plaster are too fine to be used. Risk
getting into the motor and damaging it.
1. Switch off (1) the machine and remove the
mains plug from the mains.
2. Unlock the metal locking clamps (5) and remove
the top section (8).
3. Before vacuuming, remove all dirt and debris
from the container (7).
4. Fit the filter. Carefully slide the HEPA filter (11)
over the filter holder (12) as shown in Fig. B.
5. Place the top section (8) on the container (7) as
shown in Fig. C1.
6. Reattach the top section (8) again and lock the
locking clamps (5). Fig C2.
7.
Insert one end of the hose (9) into the vacuuming
port (3). Fully unwind the suction hose (9). Fig. D.
8. Connect the mains plug.
9. Press the power switch (1) into the “ ON/1”
position to start your vacuum cleaner.
10. The machine now is ready to use for vacuum
cleaning.
11. Press the power switch (1) into the “ OFF/0”
position to switch off your vacuum cleaner.
Blow function (Fig. C1, C2, E)
Operation without the use of a filter is
recommended.
Remove all dirt and debris from the container
(7) before you use the blow function.
Always wear safety goggles before using
the blowing function.
Risk of flying objects. Keep bystanders
away from the work area.
Your vacuum cleaner is equipped with a blowing
function. It can be used to blow dust and debris out
of garages or off patios and driveways.
1. Switch off (1) the machine and remove the
mains plug from the mains.
2. Unlock the locking clamp (5) and remove the
top section (8).
3. Before blowing, remove the filter (11) and re-
move all dirt and debris from the container (7).
4. Reattach the top section (8) again and lock the
locking clamp (5). Fig. C1, C2.
5. Insert one end of the hose (9) into the blowing
port (4) on top of machine. Fully unwind the
suction hose (9). Fig. E.
6. Connect the mains plug.
7. Press the power switch (1) into the “ ON/1”
position to start your vacuum cleaner.
8. The machine is now ready for blowing dust and
debris.
9. Press the power switch (1) into the “ OFF/0”
position to switch off your vacuum cleaner.
Finish operation (Fig. F)
1. Turn off (1) the machine and disconnect the
mains plug.
2. Remove the top section (8) and empty the
container (7).
3. Clean the machine with a soft cloth.
4. Disconnect hose, tube and container.
5. Clean hose connectors, hose and tube after
use, and keep them unblocked.
6. Stow away the mains cable and accessory at
the machine as shown. Store the appliance in a
dry room.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc VC505AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc VC505AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 7,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info