764123

Vonroc VC504AC Manual

8
Zoom out
Zoom in
Previous page
1/76
Next page
8
EN
WWW.VONROC.COM
• For blowing (Fig. E-2), connect the suction
hose (17) to the blowing port (3).
5. Connect the handle (19) to the handle adapt-
er(18). One or more suction tubes (20) can be
fit to the handle (19) to extend it (fig. A).
6. Connect the desired nozzle to the handle adapt-
er(18), handle(19) or suction tubes (20).
Wet and dry floor nozzle (21)
The floor nozzle is designed for domestic wet and
dry vacuuming in, for example, the house, work
room, or garage.
Round brush nozzle (22)
The brush is designed to vacuuming solids from
small areas.
Crevice nozzle (23)
The crevice nozzle is designed for domestic wet
and dry vacuuming, edges and other areas that are
difficult to access.
Car vacuum tool (24)
The brush is designed to vacuuming solids from
small areas. For example from car seats.
Power tool adapter (25)
Adapter for connecting suction hose with a power
tool.
4. OPERATION
If the vacuum cleaner accidentally tips over,
the shut-off float (30) mechanism may
cover the motor vacuum port and stop the
suction. If this happens, simply stand the
vacuum upright and turn it off until the float
(30) returns to its normal position.
Do not vacuum without a filter!
Switching on / switching off / automatic mode
(Fig. F)
The on l / off 0 / ll automatic mode switch (1) has
three settings:
I On, power to socket.
0 Off, power to socket.
II Automatic mode, power to socket, as soon
as the power tool is switched on, the vacuum
cleaner starts with some delay. If the power tool
is switched off, the vacuum cleaner continues
to run for 5 seconds in order to vacuum up the
remaining dirt in the suction hose.
Dry vacuuming (Fig. A, C – F)
Clean the HEPA filter (27) regularly to
maintain the suction power.
To avoid the HEPA filter (27) becoming
clogged, we recommend the additional use
of a dust collection bag (26).
Fine dust, such as dust from cement, soot
and plaster are too fine to be used with only
the HEPA filter (27) and risk getting into the
motor and damaging it. Therefore we
strongly recommend a dust collection bag
(26) when cleaning these types of materials.
Clogged dust collection bag (26) can burst
– therefore make sure to replace the dust
collection bag in a timely manner!
1. Press the power switch (1) into the “ OFF/0”
position and remove the mains plug from the
mains.
2. Unlock the locking clamp (7) and remove the
top section (6).
3. Before vacuuming, remove all dirt and debris
from the container (8).
4. Carefully slide HEPA filter (27) down over the
filter cage (31) making sure the whole cage
(31) is covered as shown in Fig. C-1.
5. For vacuuming with dust collection bag (26):
• Hold the cardboard collar tightly and slide
the rubber protective element as far as
possible onto the intake port (29) as shown
in Fig. D.
• When everything is in place, unfold the bag
(26) out and position it around the inside
walls of the container (8).
6. Reattach the top section (6) again and lock the
locking clamp (7).
7. Insert one end of the hose (17) into the vacuum-
ing port (14). Fully unwind the suction hose (17).
For vacuuming:
8. Connect the mains plug.
9. Press the power switch (1) into the “ ON/I” posi-
tion to start your vacuum cleaner.
10. The machine now is ready to use for dry vacuum
cleaning.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc VC504AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc VC504AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 9,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info