Manual Vonroc S4_LM504DC (page 14 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

778579

Zoom out

Zoom in

1/128

WWW.VONROC.COM

Assembling the lower handle (Fig. A, B)

1. Insert the lower handle (14) into the intended

hole of the lawn mower body, as shown on ﬁgu-

re B. Ensure the hole in the lower handle (14)

aligns with the hole in the lawn mower body.

2. Insert the screw in the hole and tighten by turn-

ing clockwise, as shown on ﬁgure B.

3. Repeat these steps for the other lower handle

(14).

Assembling the upper handle (Fig. A, C, D)

1. Attach the upper handle (1) to the lower handle

(14), using the supplied bolts (15B) and handle

knobs (15A) as shown on ﬁgure C. Make sure

the safety switch (3) assembly is on the right

side when standing behind the lawn mower.

2. Fixate the cable to the handle by using the

cable holder (6), as shown on ﬁgure D.

Note: When handle knobs (15A) are loosened, the

upper handle (1) can be folded down for storing

the lawn mower. Ensure that the power cable is not

caught.

Assembling and mounting the grass box

(Fig. A, E, F, G, H)

The lawn mower shall not be operated

without either the entire grass catcher or

the guard in place.

It is possible to use the lawn mower with or without

grass box. Remember though that when cutting

without the grass box, the grass box lid (11) must

be lowered. Do not operate the mower with outlet

lid lifted.

1. Join the two halves of the grass box basket

(10), as shown on ﬁgure E.

2. Mount the grass box cover (12) onto the assem-

bled grass box basket (10), as shown on ﬁgure F.

3. Mount the Grass box carrying handle (16) onto

the grass box cover (12), as shown on ﬁgure G.

4. Figure H shows a correctly assembled grass box.

5. Lift the grass box lid (11) and attach the assem-

bled grass box onto the lawn mower. Ensure the

indents in the grass box align properly with the

holders of the lawn mower body.

Note: the grass box is ﬁtted with a grass level

indicator (13), which shows the amount of mowed

grass. As long as the grass box is not full, the indi-

cator will be opened. When the grass box is full, the

indicator will close. In that case immediately stop

mowing and empty the grass box. This indicator is

only a rough guideline, of which the functionality

depends on the condition inside the grass basket.

Replacing the cutting blade (Fig. A, M)

Before any work on the power tool, remove

the battery.

When replacing the cutting blade, wear

protective gloves. Danger of injury when

touching the cutting blade.

Only use blades that are recommended by

the manufacturer.

1. Remove the grass box.

2. Turn the mower onto its side.

3. Firmly hold cutting blade using protective gloves.

4. Turn the cutting blade ﬁxing screw counter-

clockwise to loosen it, as shown on ﬁgure M.

5. Replace or sharpen the cutting blade.

6. Install the cutting blade, use the above pro-

cedure in reversed order (holes in the cutting

blade must be seated on the spindle pins).

7. It is best to entrust sharpening or replacement

of cutting blade to a qualiﬁed person. Only

original parts should be used. All defects should

be repaired by service workshop authorized by

the manufacturer.

4. OPERATION

Before using, always visually inspect to see

that the blades, blade bolts and cutter

assembly are not worn or damaged. Please

remove the battery from the tool. Replace

worn or damaged blades and bolts in sets

to preserve balance.

If the machine starts to vibrate abnormally

(check immediately):

- inspect for damage,

- replace or repair any damaged parts,

- check for and tighten any loose parts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S4_LM504DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 19.43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc S4_LM504DC Manual

Product: