763972

Vonroc S3-CD502DC Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
8
EN
WWW.VONROC.COM
Fitting and removing drills or screwdriver bits (Fig. D)
Always remove the battery before mounting
an accessory.
The drill chuck (7) is suitable for drills and screw driver
bits with round shaft as well as hexagonal shaft.
• Hold the machine firmly with one hand
• Open the drill chuck (7) by rotating the chuck
with your other hand in clockwise direction until
it is opened far enough for the bit to slide in.
• Insert the shaft of the drill or screwdriver bit
• Tighten the drill chuck again by firmly rotating
the chuck (7) counterclockwise.
• Check if the bit is centered well by shortly acti-
vating the machine´s on/off switch.
Adjusting the gears (Fig. D)
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between both
positions, this will damage your machine.
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (8) forward
or backwards. The number on the gear switch (8)
shows which position is chosen.
• Position 1: For slow drilling, large drilling dia-
meter or screw driving. The machine has high
power at a low speed.
• Position 2: For fast drilling or small drilling
diameter
Adjusting the direction of rotation (Fig. E)
• Set the direction switch (9) to position in
order to drive screws or to use it for drilling.
• Set the direction switch (9) to position in
order to remove screws.
Switching the machine on and off (Fig. E)
The on/off switch (10) is used for activating the
machine and adjusting rotation speed.
• Pressing the on/off switch (10) will activate
the machine, the further the switch is being
pushed, the faster the drill will turn.
• Releasing the on/off switch (10) will stop the
machine.
• Move the direction reversing switch (9) to the
middle position to lock the movement of the on/
off switch.
Adjusting the torque (Fig. E)
The machine has 17 different torque settings and a
special drill mode to set the power being transmit-
ted to the chuck.
By rotating the torque adjustment ring (11), screws
can be driven to a predetermined depth, which is
ideal for repetitive work. The higher the number,
the more torque will be transmitted.
• Select a low setting for small screws or soft
work material.
• Select a high setting for large screws, hard
work materials and when removing screws.
• You should preferably choose a setting as
low as possible when driving screws. Select
a higher setting if the motor slips before the
screw is fully tightened.
• For drilling, turn the torque adjustment ring (11)
to the setting for drilling ( ) by fully turning
it counterclockwise.
Ensure that the direction switch (9) is
always set to during drilling.
The machine is equipped with electronic
overload protection function. When the
machine gets overloaded it will shut down
automatically. When this happens, please
wait for a few seconds to let the overload
protection reset itself.
4. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S3-CD502DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S3-CD502DC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info