764085

Vonroc S2-AG501DC Manual

13
Zoom out
Zoom in
Previous page
1/72
Next page
EN
13
WWW.VONROC.COM
the on/off switch (5) in the direction of the
grinding disc (fig. B1).
• To switch off the machine, press the lower part
of the on/off switch (5) (fig. B2). Hold the ma-
chine away from the work piece when turning
it on and off because the wheel disc could
damage the work piece.
•
Clamp the work piece firmly or use another me-
thod to ensure that it cannot move while working.
• Check the discs regularly. Worn wheel discs
have a negative effect on the machine’s effici-
ency. Change to a new wheel disc in good time.
Deburring (Fig. H)
An angle of inclination of 300 to 400 will
give the best results when deburring. Move
the machine back and forth using light
pressure. This will prevent the work piece
from discolouring or becoming too hot and
will avoid making groves.
Never use abrasive cutting discs for
deburring work!
Cutting (Fig. I)
For cutting, a special protection guard must
be used (not included).
Maintain firm contact with the work piece to
prevent vibration and do not tilt or apply pressure
and when cutting. Use moderate pressure when
working, appropriate to the material that is being
worked on. Do not slow down wheel discs by
applying sideways counter pressure. The direction
in which you want to cut is important. The machine
must always work against the direction of the cut;
so never move the machine in the other direction!
There is the risk that the machine will catch in the
cut causing kickback and that you will lose control.
Hints for optimum use
• Clamp the work piece. Use a clamping device
for small work pieces.
• Hold the machine with both hands.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the wheel disc on the work piece.
• Slowly move the machine along the work piece,
firm ly pressing the wheel disc against the work
piece.
•
Do not apply too much pressure on the machine.
Let the machine do the work.
• Switch off the machine and wait for the machine
to come to a complete standstill before putting
the machine down.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth moi-
stened with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.
WARRANTY
VONROC products are developed to the highest
quality standards and are guaranteed free of
defects in both materials and workmanship for the
period lawfully stipulated starting from the date of
original purchase. Should the product develop any
failure during this period due to defective material
and/or workmanship then contact VONROC directly.
The following circumstances are excluded from this
guarantee:
• Repairs and or alterations have been made
or attempted to the machine by unauthorized
service centers;
• Normal wear and tear;
• The tool has been abused, misused or
improperly maintained;
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S2-AG501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S2-AG501DC in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info