764085

Vonroc S2-AG501DC Manual

12
Zoom out
Zoom in
Previous page
1/72
Next page
12
EN
WWW.VONROC.COM
the battery has left.
•
When the lights are not burning it means the bat-
tery is empty and must be charged immediately.
Charging the battery with the charger (Fig. C-2)
1. Take the battery (13) from the machine.
2. Turn the battery (13) to upside down position and
slide it onto the charger (17) as shown in Fig. C-2.
3. Push the battery until it is fully pushed into the
slot.
4.
Plug the charger plug into an electrical outlet and
wait for a while. The LED indicators on the charger
(18) will lighten up and show the charger status.
The charger has 2 LED indicators (18) which indica-
te
the status of the charging process:
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
finished
On Off Battery charging in
progress
• Fully charging the 2Ah battery may take up to
60 minutes.
• Fully charging the 4Ah battery may take up to
120 minutes.
After the battery is fully charged remove the char-
ger plug from the outlet and remove the battery
from the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Assembling the protection guard (Fig. E and F)
1. Place the machine on a table with the spindle
(7) facing upwards.
2. Place the protection guard (3) over the machine
head as shown in Figure E making sure the
ridges on the protection guard fall into the
notches of the machine head.
3. Turn the protection guard counter clockwise as
shown in Figure F and clench the release lever
for protection guard (2).
4. You can adjust the position of the protection
guard by releasing the lever (2), adjust the
guard to the desired position and clench the
lever to lock it.
Mounting and removing the wheel disc (Fig. D)
Do not use the machine without the guard.
Only use sharp and undamaged wheel
discs.
• Always use suitable wheel disc for this machine
with diameter Ø 115 mm and a bore from
22.2 mm the thickness of the wheel disc should
be 6 mm for wheel disc for grinding and 3 mm
for wheel disc for cutting, the mounting wheel
disc may not touch the safety guard.
Mounting
1. Place the machine on a table with the protecti-
on guard (3) facing upwards.
2. Mount the flange (9) onto the spindle (7).
3. Place the wheel disc (10) onto the spindle (7).
4. Keep the spindle lock button (1) pressed and
firmly tighten the clamping nut (11) onto the
spindle (7) by using the spanner (12).
Removing
1. Place the machine on a table with the protecti-
on guard (3) facing upwards.
2. Keep the spindle lock button (1) pressed and
loosen the clamping nut (11) using the spanner
(12).
3.
Remove the wheel disc (10) from the spindle (7).
4. Keep the spindle lock button (1) pressed and
firmly tighten the clamping nut (11) using the
spanner (12).
Mounting the side handle (Fig. A and G)
• The side handle (8) can be screwed into one of
the three side handle connection points (6).
4. OPERATION
Make sure that the work piece is properly
supported or fixed.
Switching on and off (Fig. B)
• To switch on the machine in continuous mode,
slide the on/off switch (5) to the right and slide
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc S2-AG501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc S2-AG501DC in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info