778583

Vonroc PW506AC Manual

10
Zoom out
Zoom in
Previous page
1/76
Next page
10
EN
WWW.VONROC.COM
cloth moistened with soapsuds. Do not use any
solvents such as gasoline, alcohol, ammonia, etc.
Chemicals such as these will damage the synthetic
components.
Water inlet filter (Fig. A)
The water inlet filter (3) must be inspected
regularly, so as to avoid blockage and restriction of
the water supply to the pump.
Cleaning nozzle (Fig. A, F)
When the nozzle is clogged, it may cause failure.
The nozzle can be cleaned by inserting the
‘cleaning pin’ (13) into the tip to remove filth.
Storage and frost protection
The high pressure cleaner and accessories that are
not completely drained can be destroyed by frost.
Completely drain the high pressure cleaner and
accessories and protect them against frost.
Keep the high pressure cleaner in well-ventilated dry
premises with temperature not going below +5°C.
MALFUNCTION
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
1. When switched on, the machine will not start
working.
• Plug is not well connected or electric socket is
faulty.
• Check plug, socket and fuse.
• The mains voltage is lower than the minimum
requirement for start up.
• Check that the mains voltage is adequate.
• The pump is stuck.
• Refer to after storage instructions. Switch
off the unit and let the motor cool.
• Thermal safety has tripped.
• Leave the lance open with water coming
through.
2. Fluctuating pressure
• Pump sucking air.
• Check that hoses and connections are
airtight.
• Valves dirty, worn out or stuck. Pump seals
worn.
• Clean and replace or refer to dealer.
3. Water leaking from the pump
• Seals worn out.
• Check and replace, or refer to dealer.
4. The motor stops suddenly
• Thermal safety switch has tripped due to
overheating.
• Check that the mains voltage corresponds
to specifications. An extension cable, which
is too thin, and too long can cause a voltage
drop and cause the motor to overheat.
Leave to cool down. Use heavy duty
extension cables.
5. The pump does not reach the necessary
pressure.
• Water inlet, filter is clogged.
• Clean the water inlet filter.
• Pump sucking air from connections or hoses.
• Check that all supply connections are tight.
• Suction/ delivery valves are clogged or worn
out.
• Check that the water feeding hose is not
leaking.
• Unloader valve is stuck.
• Clear or respire valves.
• Lance nozzle incorrect or worn out.
• Loosen and re-tighten regulation screw
check and/ or replace.
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PW506AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PW506AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info