778583
8
Zoom out
Zoom in
Previous page
1/76
Next page
8
EN
WWW.VONROC.COM
preventer in the water pipe to prevent dirty
water flow back to the drinking water system.
The backflow preventer shall comply with EN
60335-2-79 ANNEX AA.
2. MACHINE INFORMATION
Intended use
The high pressure cleaner PW506AC is quick and
efficient for cleaning vehicles, machines, boats,
buildings, etc. Only clean vehicle engines in areas
in which suitable oil traps are installed.
TECHNICAL SPECIFICATIONS
Model No. PW506AC
Voltage 220-240 V~ 50/60Hz
Input power 2200 W
Max. pressure water supply 12 bar
Max. water temperature 50 °C
Rated flow rate 6.5 l/min
Max. flow rate 7.5 l/min
Rated pressure 120 bar
Max. pressure 170 bar
Weight 12.14 kg
IP class IPX5
Protective class II
Lpa (sound pressure) 74.6 dB(A) K=3dB(A)
Lwa (sound power) 88.3 dB(A) K=3dB(A)
Max. LwA (sound power) 89 dB(A)
Vibration 2.089 m/s
2
DESCRIPTION
The numbers in the text refer to the diagrams on
pages 2-5.
1. High pressure cleaner
2. On/off switch
3. Water inlet filter
4. Hose holder
5. Water outlet
6. Gun holder
7. Handle
8. Cable holder
9. Spray gun
10. Adjustable spray lance
11. Turbo lance
12. Nozzle holder
13. Cleaning needle
14. Detergent tank
15. Adapter from thread to quick connector
16. High pressure hose
17. Detergent adjustment
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Assembly of the handle and hose holder (Fig. A, B1)
1. Assemble handle (7) and hose holder (4) as
shown in Fig. B1.
2. Tighten the screws.
Assembly of the gun holder, cable holder and
nozzle holder (Fig. A, B2)
Assemble gun holder (6), cable holder (8) and
nozzle holder (12) as shown in Fig. B2.
4. OPERATION
The machine may cause electrical
disturbances when starting.
The motor of this pressure washer will NOT
run. It will only operate when the trigger is
squeezed.
The cleaner must only be used with clean
water; use of unfiltered water or corrosive
chemicals will damage the cleaner.
If the motor stops and fails to restart, wait
2-3 minutes before restarting. THERMAL
CUTOUT TRIPPED.
Turning on (Fig. A, C)
1. Turn the switch (2) to the “OFF/0” position.
2. Ensure that you have a suitable water supply to
feed the pressure washer.
3. Connect lance (10 / 11) as shown in Fig. C1.
4. Connect the high pressure hose (16) to the
washer as shown in Fig. C2 and connect the
spray gun (9) to the high pressure hose (16) as
shown in Fig. C3.
5.
Check gauze filter (3) is clear of any blockage and
assemble on the machine as shown in Fig. C4.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc PW506AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc PW506AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info