764100

Vonroc JS503AC Manual

7
Zoom out
Zoom in
Previous page
1/48
Next page
EN
7
WWW.VONROC.COM
4. Auxiliary handle
5. Speed adjustment wheel
6. Pendulum action switch
7. Scale for bevel angle
8. Vacuum cleaner adapter
9. Baseplate
10. Guide roller
11. Clamping lever
12. Bolts for parallel guide
13. Hex key
14. Chuck
15. Saw blade
16. Bolt for baseplate
17. Parallel guide
18. Cutting mark
3. ASSEMBLY
Replacing the saw blade (Fig. A, B)
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond with
the characteristic data given in the
operating instructions.
Mounting the saw blade
Make sure the blade holder is free of material
debris (such as splinters of wood or metal).
1. Turn the clamping lever (11) as far to the left as
possible and hold it in this position.
2. Insert the saw blade in the chuck (14). Check
that the saw blade is securely fixed and that the
teeth are pointing in the cutting direction.
3. Let go of the clamping lever. Check whether the
back of the saw blade is positioned in the cent-
re of the guide roller (10). Make sure to use the
right sawblade for the corresponding material.
Included with the machine is a coarse sawblade
for wood and a fine sawblade for metal and
plastics.
Removing the saw blade
1. Turn the clamping lever (11) as far to the left as
possible and hold it in this position.
2. Remove the saw blade from the chuck (14).
3. Let go of the clamping lever.
Attaching the parallel guide (Fig. C)
1. Loosen the bolts (12).
2.
Mount the parallel guide (17) onto the baseplate
(9).
3. Set the desired cutting width using the scale
on the parallel guide (17) and the cutting mark
on the baseplate (9). The cutting mark (18)
indicates the position of the saw blade.
4. Tighten the bolts (12).
4. OPERATION
Switching on and off (Fig. A)
• To switch the machine on, push the switch
forward and press the On/off switch (1).
• To switch the machine off, release the On/off
switch (1).
Setting the speed (Fig. A)
The speed adjustment wheel (5) is used for setting
the speed. The ideal speed depends on the profile
and the teeth of the saw blade and on the material
to be worked.
Do not set the speed during use.
• Turn the speed adjustment wheel (5) to the
required position.
- For hard materials, use a saw blade with
fine teeth and select a lower speed.
- For soft materials, use a saw blade with
coarse teeth and select a higher speed.
Adjusting the bevel angle (Fig. A, D)
1. Loosen the bolts (16), using the hex key (13).
2. Adjust the baseplate (9) to the desired position
(0°- 45°). The sawing angle (bevel) can be read
on the scale (7).
3. Tighten the bolts (16), using the hex key (13). It
is possible to store the hex key onto the machi-
ne, as shown on Fig. A.
Adjusting the pendulum action (Fig. A)
The pendulum action switch (6) is used to set the
way in which the teeth of the saw blade grip the
material. The pendulum action switch can be set
to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc JS503AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc JS503AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info