778543

Vonroc ID501AC Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
EN
WWW.VONROC.COM
Before exchanging bits, first remove the
power plug from the wall socket.
Inspect bits regularly during use. Blunt
bits should be re-sharpened or replaced.
• Open the chuck (1) by turning the front sleeve
(11) clockwise while simultaneously holding the
rear sleeve (10) or turning it counterclockwise
and insert the bit into the chuck opening.
• Tighten the bit by turning the front sleeve (11)
counterclockwise while simultaneously holding
the rear sleeve (10) or turning it clockwise.
Setting depth stop (Fig. C)
• Insert the depth stop (3) in the hole in the side
handle ring.
• Slide the ruler to the desired depth.
4. OPERATIONS
Impact drills require very little operator
pressure. Excessive pressure on the tool
can lead to unnecessary overheating of the
motor, and burning of the driven tool.
The On/Off switch (Fig. A)
• Switch the machine on by pressing the On/Off
switch (5). When you release the On/Off switch
(5) the machine will turn off.
• The rotation-speed can be adjusted by pressing
the On/Off switch (5) harder for raising the
rotation-speed or release pressure for lowering
the rotation-speed.
Lock-on Button (Fig. A)
• You can lock the On/Off switch (5) by pressing
the On/Off switch (5) and then pressing the
lock-on button (4).
• To release the switch-lock; shortly press the
On/Off switch (5) again.
Adjusting of the maximum rotation speed (Fig. A)
•
Adjust the speed by turning the speed adjustment
wheel (6) to the desired maximum rotation speed.
Switching the direction of rotation (Fig. A)
Do not change the direction of rotation
during use.
• Direction of rotation counter-clockwise: shift
left/right rotation switch (7) to ‘‘L’’.
• Direction of rotation clockwise: shift left/right
rotation switch (7) to ‘‘R’’.
Function selection switch (Fig. A)
In order to avoid damage to the machine,
adjusting the function selection switch (2)
shall only be done when machine is not
running.
• Set the function selection switch (2) to “ ”
for drilling.
• Set the function selection switch (2) to “
”
for hammer drilling.
User tips
Always use the machine with the side handle firmly
anchored in place - you will not only work with more
comfort, you will also work with more precision.
Caution: drilling bits and hammer drilling
bits can get very hot.
Drilling and hammer drilling
•
For large holes, for instance in very hard concrete,
start using a smaller bit for pilot drilling first, then
drill to nominal size.
• Hold the machine firmly with 2 hands. Be aware
the drill can jam and because of that machine
might suddenly turn (Especially when drilling
deep holes).
• Do not apply a lot of pressure on the machine,
let the machine do the work.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc ID501AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc ID501AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info