778575

Vonroc GT502AC Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
8
EN
WWW.VONROC.COM
5. Power cable
6. Upper housing
7. Lower housing
8. Protection guard
9. Spool assembly
10. Housing screw
11. Protection guard screw
12. Notch
13. Blade
14. Spool cover
15. Wire spool
16. Spring
17. Spool holder
3. ASSEMBLY
Cut injury when the unit starts accidentally.
Before you assemble the unit, make sure
that the mains cable is disconnected.
Assembling the housing (Fig. A, B, C)
1. Insert the lower housing (7) into the upper
housing (6), as shown on figure B. Ensure that
the cable is not stretched or caught when you
do this.
2. Secure both housing parts using the housing
screws (10), as shown on figure C. Use a screw
on both sides of the housing.
Mounting the protection guard (Fig. A, D)
1. Put the protection guard (8) onto the lower hou-
sing (7) by first putting the guard into the notch
(12) and afterwards pulling the guard upwards.
2. Now secure the protection guard using the pro-
tection guard screw (11). A correctly assembled
protection guard is shown on figure D.
Replacing the wire spool (Fig. F1)
Before replacing the spool clean the
machine from any dirt.
• Remove the spool cover (14) by pressing the
two buttons on each side of the spool cover.
• Take out the spool reel (15) but leave the spring
(16) inside.
• Take the new spool reel (GT802AA) and place
it over the spring (16). Make sure the wires
are passed through the holes inside the spool
holder (17).
• Cover the new spool reel with the spool cover
(14) and make sure the buttons of the spool
cover (14) align properly with the holes inside
the spool holder (17).
4. OPERATION
Using the tap and go system (Fig. A, D)
To enable the tap and go system, the plastic cover
in front of the blade (13) in the protection guard (8)
must be removed.
Do not touch the blade (13) in the
protection guard (8) to prevent injury.
• When the wire is too short, switch the machine
on and press the tip of the spool reel (15) on
the ground (make sure this is done on a hard
surface).
• This will release the wire in order to get longer.
• The wire will be cut on the correct length
automatically by the blade (13) mounted in the
protection guard (8).
Using the cord grip (fig. A, E)
To help secure the plug to the extension cord,
make a loop in the extension cord and attach it to
the cable hook as shown (see Fig. E). Once secure,
attach the cord to the plug. This will prevent acci-
dental ‘pull-out’.
Using the trimmer
Before use, always visually inspect the
machine and its parts are correctly
mounted, not worn out or damaged.
Hold the unit by the top part of the handle (1) and
the front handle (4) so that the trimmer head is
tilted a small distance forward. Make sure, the
filament does not touch hard objects such as walls,
stones and fences to prevent the filament from
welding together or breaking.
Switching On and Off (fig. A)
• To switch the trimmer on, press the on/off
switch (2).
• To switch off, simply release the on/off switch
(2).
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc GT502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc GT502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 7.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info