778592

Vonroc GS502AC Manual

7
Zoom out
Zoom in
Previous page
1/84
Next page
EN
7
WWW.VONROC.COM
• This appliance is for outdoor use only.
• Do not expose this appliance to rain.
• Use the shredder only in daylight or good artifi-
cial light.
• Never leave the appliance unattended.
• Do not use the appliance in an area where it
could cause an explosion or fire - keep it away
from flammable liquids and gases.
• Guard against electric shock - prevent body
contact with earthed or grounded surfaces i.e.
metal gates, posts or other metal objects in the
work area.
• Never pull the appliance by its power cord.
Wheel it or carry it with two hands.
• Do not allow the power cord to lay on or across
sharp objects that might pierce the outer insu-
lation. Carry out a visual inspection of the power
cord before use and if it is damaged, have it
replaced by a specialist service centre. Do not
use the appliance if the cord is damaged.
• Keep the power cord away from heat, frost, oil,
solvents or any sharp objects or edges.
•
Do not use this appliance if you are on strong
medication, unwell or have been drinking alcohol.
• Never attempt to put your hand inside the fee-
der hopper. If you want to push material into the
cutting chamber use the push stick.
• Before starting the machine, look into the fee-
ding chamber to make certain that it is empty.
• Keep your face and body away from the feed
intake opening.
• Do not allow hands or any other part of the body
or clothing inside the feeding chamber, dischar-
ge chute, or near any moving part.
• Keep proper balance and footing at all times.
Do not overreach. Never stand at a higher level
than the base of the machine when feeding
material into it.
• Always stand clear of the discharge zone when
operating this machine.
• When feeding material into the machine be
extremely careful that pieces of metal, rocks,
bottles, cans or other foreign objects are not
included.
• If the cutting mechanism strikes any foreign ob-
jects or if the machine should start making any
unusual noise or vibration, shut off the power
source and allow the machine to stop (electric
unit disconnect from supply):
• inspect for damage
• check for and tighten any loose parts
• have any damaged parts replaced or repaired
and use only the manufacturer's recom-
mended replacement parts and accessories.
• Do not allow processed material to build up in
the discharge zone; this may prevent proper
discharge and can result in kickback of material
through the feed intake opening.
• If the machine becomes clogged, shut-off the
power source (electric unit disconnect from
supply) before clearing debris. Keep the power
source clear of debris and other accumulations
to prevent damage to the power source or pos-
sible fire. Remember that operating the starting
mechanism on engine powered machines will
still cause the cutting means to move.
• Keep all guards and deflectors in place and in
good working condition.
• Do not tamper with the power source governor
settings; the governor controls the safe maxi-
mum operating speed and protects the power
source and all moving parts from damage
caused by over-speed. Seek authorized service
if a problem exists.
• Do not transport this machine while the power
source is running.
• Shut off the power source and disconnect from
supply whenever you leave the work area.
• Do not tilt the machine while the power source
is running.
• Your shredder must be placed on firm, level
ground.
• Never lay the shredder on its back, front or
sides - keep it upright at all times.
• Do not overload the shredder - feed it slowly
and let it work at its own pace.
• Before starting, ensure the inlet cavity is empty.
Do not start the shredder with material in the
shredder.
• Unless there is an emergency, do not switch
the shredder off until it is completely empty of
material.
• Remove stones or other hard objects from plant
roots before shredding.
• Hold large twigs or fine branches firmly when
feeding them into the shredder.
• Do not allow the outlet to get covered or bloc-
ked at any time.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc GS502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc GS502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info