778592

Vonroc GS502AC Manual

6
Zoom out
Zoom in
Previous page
1/84
Next page
6
EN
WWW.VONROC.COM
f)
Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
NOTE The temperature „130 °C“ can be replaced
by the temperature „265 °F“.
g)
Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b)
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
ADDITIONAL SAFETY INSTRUCTION FOR
SHREDDERS
• Only use this shredder when a Residual Current
Device (RCD) with a tripping current of not more
than 30mA is in the circuit.
• If an extension cord is used make sure it is for
outdoor use and marked as such. The recom-
mended size of extension cord is a H05VV-F or
H05RN-F type, not lighter than 1.5 mm and a
maximum of 10 metres in length.
• Completely uncoil your extension cable before
use to prevent overheating and loss of machine
efficiency. When tidying away the cable, wind it
carefully to avoid kinking.
• This appliance is not intended for use by per-
sons (including children) with reduced physical,
sensory or mental capabilities, or lack of expe-
rience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
WARNING: After switching off the machine,
the cutting blade continues to rotate for a
few more seconds.
• Frequently inspect the condition of the cutting
blade. Damaged blade must be replaced im-
mediately. Follow all the required precautions
when replacing the blade.
• Before use check the supply and extension
cord for signs of damage or ageing. If the cord
becomes damaged during use, disconnect the
cord from the supply immediately.
• DO NOT TOUCH THE CORD BEFORE DISCONNEC-
TING THE SUPPLY.
• Not to connect a damaged cord to the supply or
touch a damaged cord before it is disconnected
from the supply. A damaged cord can lead to
contact with live parts.
• Do not use the shredder if the cord is damaged
or worn.
• Read the instructions carefully. Be familiar with
the controls and proper use of the equipment.
Avoid using the machine in bad weather condi-
tions especially when there is a risk of lightning.
Always wear substantial footwear and long
trousers while operating the machine.
•
Keep children and pets well away from the work
area and never allow children to use this applian-
ce or touch the main power cord or extension cord
at any time. When not in use, keep this appliance
stored in a safe place out of reach of children.
WARNING: In order to reduce the risk,
disconnect the plug from the supply power,
only use recommended accessories as
required, otherwise personal injury may
result.
• Wear ear protection and safety glasses at all
times while operating the machine
• Wear a dust protection if the shredding action
causes the raising of dust or particles.
• Dress sensibly for the job in hand - no loose
clothing that could get caught in the moving
parts of the appliance.
• Pull long hair back out of the way and wear a
protective hat.
• Only operate the machine in open space (e.g.
not close to a wall or other fixed object) and on
a firm, level surface.
•
Do not operate the machine on a paved or gravel
surface where ejected material could cause injury.
• Thoroughly inspect the shredder for loose or
damaged parts before each use. Do not use the
unit until adjustments or repairs are made.
• Replace damaged or unreadable labels.
• Only use a waterproof, fully unwound extension
cable suitable for outdoor use.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc GS502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc GS502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info