Manual Vonroc GG502DC (page 6 of 44) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

778546

Zoom out

Zoom in

1/44

WWW.VONROC.COM

LED Charger status

Red Battery charging in progress.

Green Battery charging ﬁnished, battery fully

charged.

• After the battery is fully charged remove the

charger plug from the outlet and remove the

small plug from the base.

• Fully charging the battery may take up to 2 – 3

hours.

Inserting glue sticks (11) (Fig. D)

Always use the correct diameter glue stick.

1. Insert a glue stick through the opening at the

back of the glue gun.

2. Guide the glue stick into the glue chamber until

it stops.

The glue gun will stop dispensing glue when the

glue stick in the chamber is almost used up. To

reﬁll the chamber, set the glue gun in the base and

insert a new glue stick.

Switching the machine on and off (Fig. A)

• Press and hold the on/off switch (5) to turn on

the glue gun until the heat up LED indicator (4)

will light on in RED.

• Allow approx. 25 seconds for the glue to melt

and reached the operating temperature and the

heat up LED indicator (4) will turn green.

• The glue gun is ready for use.

NOTE: The heat up LED indicator appeared RED and

you feel resistance from the trigger during applica-

tion, then the glue gun will be required to reheating

for a few seconds.

Using the glue gun

• Hold the glue gun ﬁrmly and place the nozzle

close to the surface where glue will be applied.

• Pull the trigger (1) until glue ﬂows from the

nozzle (3), do not over-apply.

• When the desired amount of glue has been ap-

plied, release the trigger (1). Tilt the nozzle (3)

slightly to the side and carefully pull the nozzle

away from the object. This helps avoid strings

of glue clinging to the work.

• Between application use the base to tempora-

rily store the glue gun, glue gun will automati-

cally charge.

NOTE: The glue gun will be automatically shut-off

after approximately 5 minutes if not in use. You

need to press the ON/OFF switch to restart.

Using the drip tray

• The built-in drip tray (9) on the base (2) will

catch any drips while the glue gun is heating or

cooling down.

• With your hand, simple to slide the drip tray out

from base. Like shown in ﬁgure E.

NOTE: Always turn the glue gun off and place on its

base when you are ﬁnished using the glue gun.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and dirt.

Remove very persistent dirt using a soft cloth mois-

tened with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

Clean the glue gun metal contact

Always check before each use to see that the

metal contacts are clean to give a best contact

performance when charging. Any residue should

be cleaned from the metal contacts using the

following steps.

1. Remove the glue gun from the base and set

aside.

2. Carefully scrape the cooled glue from the metal

contacts using a cotton swab or any non-metal-

lic utensil.

Be sure to check the contacts on both the glue

gun and the base for any glue residue. Never use

metallic utensils to clean the contacts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc GG502DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc GG502DC Manual

Product: